Jump to content
SAU Community

Recommended Posts

Hi have a few things laying around, need to get rid of these to fund new engine.

1. R32 Rear wing in metallic black Fits R32 ONLY....too wide for 33 - $200

2. R32 3.5inch Stainless Lobster Welded Exhaust, has 3 inch mild steel inlet then goes 3.5 all the way through with single XForce Cannon, excellent condition. $300

Located North Coast NSW

All Offers Considered, Cheers

Pics,

34337_403998070987_602510987_4884903_2238015_n.jpg

37376_403998145987_602510987_4884909_6370999_n.jpg

11442_169839230987_602510987_3319651_688881_n.jpg

11442_169839260987_602510987_3319655_4549790_n.jpg

I have absolutely no idea what type it is, fits r32 boot perfectly, looks like 33 gtr wing but its too wide for a 33 boot.

its not on my car atm i just sat it on the boot to see what it would look like.

need this stuff gone $120 wing

$250 exhaust

ono

Edited by DuFFR32

Any chance you can take a pic from the side but further out? so can see what the wing looks like in proportion with the rest of the car

Thanks for the message

I'm about 1 hr north, going away for a week will contact you when I get home and drive down and look.

Cheers Chris

I apologize for my absence on here, went to aus post to see if I can post exhaust but they wont take it cause the front pipe it too long. :P need to find courier any ideas?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...