Jump to content
SAU Community

Nismo GT Forged Conrod Set - RB26DETT

gtraaron
 Share

Recommended Posts

gtraaron Mentor

gtraaron

Posted
  • Author
Posted
That is VERY cheap for Nismo GT Spec 1 Forged Rods! - Pm sent!
IT IS NICK , IT IS AT LEAST $300 CHEAPER THAN YOU CAN GET THEM FROMNENGUN OR RHD , THATS BEFORE DELIVERY COSTS ! HERE IS SOME INFO ON THE SPECS ;The NISMO RB26DETT Engine Parts - GT Con-Rod Set Spec 1 are the connecting rods of choice for the GT500 spec Nismo race cars as well as the Nur24 hour race cars and the popular Z tune R34s. These are the Spec 1 units that have a center to center height of 119.5mm and can use the stock pistons or other pistons of 30mm piston compression height. Pin diameters are 51mm and 21mm. The Connecting rods are made from SNCM439 to achieve both a light weight and high strength qualities. You can use these with the GT500 Crank (made of similar material) to build the popular 2.8l RB motor.
gtraaron Mentor

gtraaron

Posted
  • Author
Posted
so theses are the same size as a stardard rod and can be used in a 2.6L with forged pistons?

yes thats right ! also looking at swaps for things of interest so pm me your ideas and i will say ya or nah , cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...