Jump to content
SAU Community

Recommended Posts

  • Replies 172
  • Created
  • Last Reply

Top Posters In This Topic

most half cuts go for 2500 ( r33 ) but not stagea half cuts.

u say 1500 but thats for a r33 motor, box ect not a s2 awd stagea that has a r34gtt rb25.

price is good i think

Edited by whitenight27

haha true true too much boost.

i shore goodo thinks its worth what his asking for.

the extra 1000 is because its a r34gtt and not a older r33 motor.

for 1 the turbo is a lot better than the 33.

the 34 turbo can run little more boost and has a bigger rear housing but still responsive

33 turbo has a ceramic compressor wheel while the 34 turbo has nylon compressor wheel and better for hi-flowing

i will just say don't think u will ever get a 34gtt motor ecu and piping for 1500. r33gtt yer no probs

34 will have low ks and a lot newer motor than a 33 rb25

Edited by whitenight27

whiteknight27you will have to be a little more clear when you say what is left. I prob dont have much that you need but if you ask for what you actually need i will be able to answer yes or no . As for the 34 front it went on to my new one

menthol369 sorry but the motor is gone got $2300 motor loom and ecu

thort u would get around 2k for it lol.

any how need things like

peddle box

console

hand brake and cable

any thing i would need to change my auto 2 man

I belive i do have the peddle box and clutch master cylinder but i think thats about it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...