Jump to content
SAU Community

Recommended Posts

  • Replies 106
  • Created
  • Last Reply

Top Posters In This Topic

jangles it better be the the fresh datsun, pull ur finger out.

Damo wots happening with ur drifter at the moment? how come its not running?

had an issue with the head. its always been a problem but only discovered it after a few chnages made during the rebuild. pulled the head off. fix the problem but havent put it back together yet, mainly because i wanted to put it back together and add a big turbo.

ive just started work on it again after not toutching it for 2-3 months. a lot of work ahead of me again.

I just need to sort out a bottom end it will be there

i hope to see it out there rob you have missed far to many even for my liking.

Link to comment
https://www.sau.com.au/forums/topic/339948-powercruise/#findComment-5491059
Share on other sites

LOL at all the broken RB's :) .

Should be there, pretty keen to link from the back straight onto the start finish straight again!

Ben

I'm keen to see that!

Damo, so are u adding a bigger turbo then? and wot is it? or surprise??

Link to comment
https://www.sau.com.au/forums/topic/339948-powercruise/#findComment-5492287
Share on other sites

I'm keen to see that!

Damo, so are u adding a bigger turbo then? and wot is it? or surprise??

yep its a bigger one. nothing special just the usual garret rubbish but i wont be putting any big numbers in it just yet. 260+ at this stage and then e85 later on. main concern is doing evrything right once so i wont be spending every night working on it next year.

Link to comment
https://www.sau.com.au/forums/topic/339948-powercruise/#findComment-5492767
Share on other sites

something in a RB30 block...

hmmm dont think i can help with a 30. i got a complete 25 bottom end sitting in my garage thats all.

lol yer im dying my my 3 litre to be running. engine done. just gotta save for bolt ons really.

Link to comment
https://www.sau.com.au/forums/topic/339948-powercruise/#findComment-5492961
Share on other sites

I need a 30 crank or will go with one of the stroker kits. 3.4 would be nice but then the T51 might be a little small. :)

Ive missed every powercruise so far. So Im not getting my hopes up this time as I got other things on the go. Like my new house :-)

Edited by WHITER33GTS-T
Link to comment
https://www.sau.com.au/forums/topic/339948-powercruise/#findComment-5493309
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...