Jump to content
SAU Community

Recommended Posts

Bought these recently due to having a set previously in bronze, wanted something different to the common bronze/silver/black/gunmetal...

Unfortunately they do not accomodate my new brakes.. :)

There's bugger all clearance between the caliper and rim, stupid V8 supercar brakes!!!!

So therefore I have to regretably get rid of them.

These are brand new, have not had any tyres fitted to them and have only pulled one out of the box to trial fit and take photos.

They are very hard to come by in gold, have only seen them once before in the flesh on a blue R32 GT-R in 18 x 9.5.

SPECS are pictured below:

gallery_1569_106_459898.jpg

And some pics of the wheel I removed from the box:

gallery_1569_106_154260.jpg

gallery_1569_106_288622.jpg

They look much better out in the sunlight, the finish is remarkable:

gallery_1569_106_607215.jpg

gallery_1569_106_339199.jpg

Rims are located at Racepace Motorsport in Bayswater VIC for inspection, will freight at buyer's expense, around $80 for the set along the eastern board of Australia.

PRICE: $4200 FIRM, no offers.

PM or reply here if interested....

Cheers,

Jack

Black R34 GTR Sporting Exactly These In Cabramatta.

They Look Sex...

Perfect Fitment & Stance

Also Rich Gold...

Love These!!!

Now that would look insane.

Would love to see some pics of it....

ouch Jack!! theyre definitely one of the best rims ever. shame i dont have enough cash, otherwise i'd also grab this off your hands. and i almost forget about your tyres, LOL! please feel free to text me anytime if you wanna pick them up.

anyway good luck with the sale

i found these pics of gold ce28 in the same specs:

325.jpg

DSC_1690-vi.jpg

ouch Jack!! theyre definitely one of the best rims ever. shame i dont have enough cash, otherwise i'd also grab this off your hands. and i almost forget about your tyres, LOL! please feel free to text me anytime if you wanna pick them up.

anyway good luck with the sale

i found these pics of gold ce28 in the same specs:

325.jpg

DSC_1690-vi.jpg

They do look great in that colour, that's why I got them.

Will contact you next week to pic up tyres.

Wheels still available.

how much to ship to canada?

No idea mate, but it wouldn't be cheap especially if air freighted.

Will make some enquiries.

Still for sale, reasonable offers now considered....

Just a reminder, you cannot get these readily available in this size and colour, would have to put in an order with Rays and wait 6 months or so to receive them....

These are in Melbourne ready to go to a new home....

Any reasonable offer considered....

bump for you Jack. if only these would fit to my evo.

oh your tyres are still here, please feel free to text me whenever you want to pick them up.

have a set of 17" advan rc2 and 2sets of re55's, check my thread, theyre going on an extremely cheap price.

if you're interested or know someone who might be interested, please contact me anytime. we can chuck everything on your trailer lol.

thanks :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...