Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

But how do i actually ask the owner for the car and drive it to the workshops to get the checks done, I don't think the owner would actually allow that right? is the RAA Total care inspection any good?

And btw is the regency inspection = to road worthy cert?

thats a pretty big call to make mate....my series 1 begs to differ to your theory :)

Series ones are getting old these days but i love them (hence why i have one).....if i were you mate i would take it to boost worx or willall racing or southern hitech or graham west workshop or morpowa or fours and more.....well take it to one of those workshops mentioned and get them do check it all out for ya mate....compression and leak down tests are a must AFAIK

Goodluck with how you go in getting your pride and joy mate :)

Edited by exclusive2u

Anyone can clear my doubts?

But how do i actually ask the owner for the car and drive it to the workshops to get the checks done, I don't think the owner would actually allow that right? is the RAA Total care inspection any good?

And btw is the regency inspection = to road worthy cert?

When I sold my 34 GTR, the buyer wanted me to drive the car across to the other side of town to his mate's workshop for a complete going over.

I had nothing to hide so I obliged him.......even if it did cost me approx 3 hours of my time.

In the end, if someone is serious about selling their ride and the buyer seems legit and not just a tyre kicker, it's just the sellers time that needs to be sacrificed.

Anyone can clear my doubts?

When i got my car 2 months ago

i asked the owner to meet me at a workshop

where the car was put on the hoist and a full test was done

and looking under the car is a must

because sometimes with imports the chassis rails

have been farked over by forklifts

also rust should be checked out as

salt is put on the roads in japan

and may cause some underbody rust

i bought my 96 S2 for 14.5 with 108,xxx

but thats because it was in immaculate condition

after looking for one for 2 years

i'll be buying from someone in SA so i don't think i will have to go thru regency right? just the transfer of ownership to me right?

but the thing is i called to get an insurance quote and they told me i need to have a road worthy cert to the car if not they won't insure the car

we dont have roadys in sa.

if youre buying a car from interstate, it will have to go through regency though.

I would never buy interstate unless its something worth its while. I got a car 4 weeks ago with lots of mods from nsw and I am still having trouble with regency been twice.

Ive never heard of having a road worthy in SA.

I insure with just cars and they have never asked for that.Who told you that?

All you need to do if you buy local is fill out the green slip thats with the rego and take it in to rego office and change ownership.

No need to take through regency if you buy local

P.S buy my car

i'll be buying from someone in SA so i don't think i will have to go thru regency right? just the transfer of ownership to me right?

but the thing is i called to get an insurance quote and they told me i need to have a road worthy cert to the car if not they won't insure the car

Sure they didn't mean an import plate/sticker?

I called Just Cars and while the guy was asking about the details of the car i was looking at to quote the insurance he said i needed a road worthy cert (exactly what he said) if not they wouldn't insure me

:D Sorry mate i'm actually looking more of a 'sleeper' car.. dun wish to be trailed every single day

I would never buy interstate unless its something worth its while. I got a car 4 weeks ago with lots of mods from nsw and I am still having trouble with regency been twice.

Ive never heard of having a road worthy in SA.

I insure with just cars and they have never asked for that.Who told you that?

All you need to do if you buy local is fill out the green slip thats with the rego and take it in to rego office and change ownership.

No need to take through regency if you buy local

P.S buy my car

Complying a vehicle and whether it passes is a statement as to its road worthy-ness and OEM parts(Originality). Like if bushes are worn,etc. it may not pass compliance.

Next time you call an insurance company ask them if they mean Compliance Sticker as we are one of the odd states out in terms of the "Road Worthy Certs". Did you tell him you were in SA and that they are null/void for SA?

Just Cars never asked me for a roadworthy cert!

Yup i did told him my full address and apparently he told me that. when most of the cars i see on carsales have no road worthy cert to come with.

Btw is it normal for a R33 to not have its airconditioning working? Apparently i called a few of those guys on carsales and they said their car airconditioning needs regas etc

Complying a vehicle and whether it passes is a statement as to its road worthy-ness and OEM parts(Originality). Like if bushes are worn,etc. it may not pass compliance.

Next time you call an insurance company ask them if they mean Compliance Sticker as we are one of the odd states out in terms of the "Road Worthy Certs". Did you tell him you were in SA and that they are null/void for SA?

Just Cars never asked me for a roadworthy cert!

Air con needs regas or they ripped out the air con? I have known quite a few people to pull out air con,etc to shed weight among other things.

As to being a problem, i'm not sure. The only problem with mine is a small plastic cog(Operates vents) has lost a few teeth, which results in a clunking noise behind the dash(apparently easy to fix in S1 but S2 has a airbag in the way).

If the air con did need to be regased, make them do it or negotiate a lower price because of it. However i would get the car checked over anyways even if it costs $200 and your time, as it could cost a lot more later on if you don't.

i wont buy a car if the air con is not working .....the old regas excuse usally means it's stuffed and too dear to fix .i would tell them that the aircon working is a must and if there not prepared to get it regassed for a sale you will keep looking .

air con repairs cant cost over a 1000 bucks to get running if it needs a new compressor and a service and regas

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...