Jump to content
SAU Community

Recommended Posts

hey all, i tried searching for some advice on this, but nothing found. trying to get some larger injectors for the rb25det neo, and been loking at some sylvia s15 injectors, dont want to spend oh so very much cash, im just looking at pulling out about 300kw.

from what ive read, the neo injectors are about 250cc and the s15 injectors are 480cc. so im opting for them, found some new ones from overseas a set of 6 individually bought ones will set me back 300 bucks.

some people have told me they will fit straight on, but im not 100% sure. anyone know????

cheers

Jean

Link to comment
https://www.sau.com.au/forums/topic/340675-fuel-injectors-in-rb25det-neo/
Share on other sites

aren't S15 injectors the same style side feeds that the R33 use's? so they would be a direct fit upgrade for the S1 Stagea. if you have a Neo motor, so a S2 Stagea, the injectors are top feed and the S15 ones are not a direct fit. oh and stock neo injectors are 370cc.

a couple of options if your not looking spending $1000+ on a set of jap brand injectors e.g Nismo. you could get your stock ones hiflowed, or you could look at getting a set of the siemens/deka injectors, they are basically a direct fit, you just need to replace the injector electrical plugs on the injector loom with ones that suit the siemens/deka injectors. when i upgraded mine i went for a set of 600cc Deatschwerks injectors, and they were a direct fit. from memory they cost between $600 and $650 to my door but the exchange rate is so good at the moment they could be even cheaper.

why not look at a set of GTR injectors? they are top feed and from memory 440cc, but for 300kw may be getting close to making out, so i'd look at 600cc ones mentioned above

because even though GTR injectors are top feed, they are a different style to the neo injectors. neo injectors look the same as XR6T injectors, and i believe they are close to the VQ engine's injectors i.e 350z, M35 Stagea etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...