Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

personally id go the EVO, there aint many around so you get the whole "unique factor".

id say (dont know figures here) they weigh alot less and are generally more chuckable (should that be your thing). At the end of the day, the Revolution / kittled lancer call is basically the same as the GTSt with GTR bodykit call, sure theres a HUGE performance difference, but shit, get what you want.

what pulls your pickle more ?

oh yeh, mal crockenberg, john st welshpool - www.crockenbergmotors.com.au

HEy boys

Thanks for your opinions...

I have found a R33 GTR that i love - making 600+hp in the eastern states. If the guy comes down on his price (which is not likely) i'll fly over have alook and buy it if its sweet.

BUT

It looks like the EVo path will be the way to go -

Im currently looking at a evo with a motec ecu, dms50 struts, whole lot of other mods. Which ill be able to buy for mid 40's which will leave me enough to but the TD06-25G turbo kit. So ill have a killa evo that will run 11's easily.

Daniel

what about a stagea, rs-four v? :cheers: I'm getting one.

They can be had for mid 20's and with the spare coin you could turn it into a manual autech version with an R34 front plus few more horses that will do 11's, go around corners and have people saying wtf !

Stagea are cool - BUT no interested.

What something more sporty, and sorry but no way a stagea will handle anywhere close to a evo - not sure about the GTR though..

Thanks anyway boys.

Daniel

I was going to get the GTR, but I have swung over the the evo 6.5 - due to the fact that they are:

* Are very rear and are alot newer (2000 - 2001)  

* Are more compact

* Are a fantastic handling car

* And have a fantastic engine with forged internals ( rb26 is great as well)

Well I would choose the GT-R for a couple of reasons.

I find the interior of the Lancer very crampt, I don't like the pedals, the gear lever position or action or the seat height. The GT-R on the other hand is much nicer, though I would prefer a reach adjustable steering wheel.

The GT-R has climate control, works very well. Aussie Evo 6.5 doesn't.

The sound of a straight six is pure heaven, the Evo engine has a purposeful and interesting note (when you dump the stock straw) but it doesn't do it for me. Though the RB26 note can become droning and tiring on a long trip.

And also I love the look of the BCNR33, so for me the choice is easy.

Thanks Guys

Gojira - im looking at the JDM evo - so it has climate control, but some good points never the less.

Rev - not a fan of the r32 - to old school for my liking.

Daniel

as rev said...if you want a rally car then buy an evo, but all of us love the road... and you cant explain the way an r33 gtr sits the road to anyone!!! evos look like they have an overlander kit...

i agree with gojira when it comes to the sound of a rb26 aswell.... :cheers:

personally, i've always had a soft spot for evo, albeit only the 6.5 TM edition, no other evo comes close to it :)

but i'm gonna have to say gtr, bit more costly to insure i'm sure it'll be worth it :)

adrian :P

That would be Crockenberg Motors. Malcolm is the man spinning the spanners. Top mechanic and top bloke. Used to get my old Sigma Turbo maintained by him. Located at 5/77 John Street, Welshpool, (08) 9358 0302.

As for Evo VS GT-R, I'd go GT-R all the way. Reasons, not based on a 4-door shopping trolley, won't get mistaken for a GLi riced up, plenty of good aftermarket parts (new & used) available around Australia. But then again - as most people have said you're only going to get biased decisions here.

In perth there is a ralliart GURU in Wleshpool who does all the ralliart vehicles then they come to perth for rally oz etc

for some friggin reason i have a mental blank, but its off welshpool road

 

I think that coming off a WRX the EVO tm will be a more confortable vehicle to drive. albeit alot more nimble than the wrx, and the rarity is something to look forward to.  

 

Umm in terms of price wouldnt you be closer to an R34 GTR instead of an R33. And the active Yaw control in the evo is supposed to be worth the dosh

 

and what about an M3..tee hee hee

Dan,

ive driven an Evo 6.5 and recently both an Evo 8 and an MSpec 34... id take the Evo though the 34 is a special place to be in

driving the 34, it feels faster (seat of pants) as opposed to the Evo which to be honest doesnt feel all to impressive... the interior is not as nice as the Skylines but it is newer which is a definate plus.. if possible.. try driving both like what i did and go for the one you feel most at home in

Thanks Guys

Rev - not a fan of the r32 - to old school for my liking.

Daniel

I'm with Rev.

Give the R32 another consideration as a part time/weekend car and get a conservative daily driver or bunky with the change. No stress about leaving a corolla or magna parked in a dodgy carpark on a Saturday night.

Don't have to go to my extreme tho - an ex RAC van!:Oops:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...