Jump to content
SAU Community

Recommended Posts

[sYD] 98 R34 GTT Manual 2 Door Silver GTR Rims - Mint Condition Genuine 96000Ks

Car: Nissan Skyline R34 GTT Manual 2 Door

Year: 1998

Colour: Metallic Silver

Doors: 2

Ks: 96000

Location: St George area, Sydney

Reason for selling: Renovating house - need the money.

Decription

Purchased 3 years ago from the original importer in stock standard condition. Always garaged.

The car has been tastefully modded by a mature 34yo owner looking to improve on factory without overdoing it. Not a fault with it, drive away with no dramas.

The car has very clean paint with Zero accident damage and a genuine 96000Ks. One of the best on the market today.

Strong, smooth running engine and turbo with no surprises!

Clean interior with no seat rips.

Regular filter and oil changes using quality Synthetic oil.

Piles of recipts for works completed and ownership information.

Never Dynoed.

100K service done with Gates Timing belt and new genuine Nissan waterpump.

Features

Handling:

18" R34 GTR Rims with Rays Alloy nuts - 245/45 Bridgestones all round with plenty of tread (70% +)

Bilstine shocks with extra circlip grooves cut (allows lowering easiliy if needed) - LEGAL HEIGHT!

Rear sub frame pineapples

Hicas bar

Adjustable rear camber arms, adjustable front castor rods

Whiteline Springs and fully adjustable sway bars front and back

Front slotted brake rotors - great stopping without the noise

Performance:

Full 3" exhaust from the turbo back with split dump, custom front pipe, high flow cat, and 4" HKS Superdrager cat back - LEGAL SOUND!

HKS EVC3 boost controller - stealth install - never boosted over 11psi

Iridium NGK Plugs

K&N in box airfilter - LEGAL!

Apexi radiator cap

New Boosh heavy duty battery

Interior:

JVC DVD with tilt in-dash screen

Alpine rear and Pioneer front 3 way speakers - simple but effective - Never had a need for a sub

Very high end 6 point keypad + remote immobiliser alarm

Nismo short shifter

Razo alloy gear shifter

Blue dash lights

New Oil Temp, Oil Preasure, Boost Gauge in factory position.

Factory Xenons - with in dash hight adjustment

Body:

Genuine Impul Front bar painted and fitted by Unique Autosports

Mesh inserts

Nismo front and side clear indicators

Factory dark rear windows tint - darkened glass, not film!

Legal front window tint

BONUS!: Near new NavMan GPS + Number Plates included!

Price: $19800

Ph: 0416275449

Note: Will reduce price by $1000 without rims (bring your own rims, or I can source a set of stock GTT rims for about $250).

May part trade for EG Civic or TA22 Celica - LOL worth a shot!

P1010352.jpg

P1010351.jpg

P1010353.jpg

P1010356.jpg

P1010354.jpg

P1010362.jpg

P1010361.jpg

P1010358.jpg

P1010357.jpg

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...