Jump to content
SAU Community

Recommended Posts

I have a set of R33 GT-R wheels on my car at the moment, but would like to see how much I could afford to offer W1ngnut for his epic wheels if I sold these ones first. I'm not sure how much these usually fetch, since condition would play a large part given the age of the wheels.

Currently there's a decent amount of very minor gutter rash on a few of the wheels. This is entirely cosmetic - none of it is bad. Wheels have never been damaged. All have centre caps. All currently balanced with current tyres

Tyres themselves are so-so. Rears have horrible camber wear on the inside, but outside tread is still good. Can't give a %, but they wouldn't be considered legal given the camber wear. Fronts are perfectly legal, HEAPS of tread left.

Throw offers at me guys, but no point low balling me as I'm not trying to get rid of them - merely seeing how much people will pay. I WILL sell them for the right price though.

Will ship at buyer's expense for interstate sales, but would naturally rather a local sale.

As per forums rules (D'OH) I would like to fetch $1200 for the wheels. Open to offers, but don't low ball me still.

Edited by Trozzle
Link to comment
https://www.sau.com.au/forums/topic/342286-eoi-r33-gt-r-wheels/
Share on other sites

I paid $1500 for a set about a month ago but they came with 6 brand new tyres and the rims had just come back from the painters and not one cm of gutter rush on them at all.

Most sets I have seen with slight gutter rash and ok tyres are around the $1000-$1200 mark and for some reason SA where I live 33 gtr rims can be difficult to find.

$1000 FIRM guys, take em away! Pics on request if you want them. This is as low as I'll go guys, any lower than this and I can't afford the bloody replacement rims lol

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...