Jump to content
SAU Community

Recommended Posts

Hi guys,

We're holding a Social Event at Simworld in Carousel on Friday the 26th of November, starting at 6pm, and going for two hours, including food from Nandos :)

For those who don't know what SimWorld is check it out at http://www.simworld.com.au/ These are full simulators, where you get thrown about etc, nothing like anything you've done before.

The general format of the event is:

Group 1 - 5min Practice - Bathurst

Group 2 - 5min Practice - Bathurst

Group 1 - 10min Race 1

Group 2 - 10min Race 1

Group 1 - 15min Race 2

Group 2 - 15min Race 2

Group 1 - 5min Practice - Nurburgring

Group 2 - 5min Practice - Nurburgring

Group 1 - 10min Race 3

Group 2 - 10min Race 3

Group 1 - 10min Race 4

Group 2 - 10min Race 4

Final - 10min Race (combined results from Race 1, 2, 3 & 4 will determine who is in the finals)

* Minimum race time is 55mins

** Comes with food supplied by Nando's, and we can have BYO drinks

*** Group size is 9, as there are 9 Simulators

Note:

The costs $70, and needs to be paid ASAP so we can make sure this happens.

The cars will be R32 GTR's, and we'll race Bathurst and Nurburgring to bring back some Skyline history.

The a full race simulators, not simple arcade games, so it will definately be an experince.

Please register your interest ASAP, so we can make this event happen. Please invite family members (friends, wives, older kids etc), as all Simulators are equal, and doesn't require a drivers license :rofl2: We'd like to have this filled with SAUWA Members and there familys/friends, but will open it up to the rest of SAU if we don't fill the spots quickly.

Cheers

Paul

SAUWA Account Details

Daniel W Brady

BSB: 016359

Account# 571542655

Description: Simworld" SAU Username"

1. GTS-t VSPEC - Paid

2. Pattygtst - Paid

3. Pattygtst (mate 1) - paid

4. Pattygtst (mate 2) - paid

5. Ashy Larry

6. Ashy Larry

7. Pal - Paid

8. Leadfoot - Paid

9. StinkyRooster - Paid

10. trikdoutvl - Paid

11. trikdoutvl (mate 1) - paid

12. COOTS - Paid

13. COOTS (mate 1)- Paid

14. Mr Eps

15. Mikey -paid

16. Mikey (mate 1) -paid

17.

18.

Reserve List:

ZXY

Link to comment
https://www.sau.com.au/forums/topic/342976-simworld-friday-26th-november/
Share on other sites

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...