Jump to content
SAU Community

Recommended Posts

This is a expression of intrests sale.

Twin HKS 25/30s

Twin turbo manifolds unknown brand.

Mines sports division stainless dump pipes

Veil side twin Stainless front pipe to single collector cat

2 rb25 green lable airflow meters good for about 550 hp atws direct plug in.

HKS mushroom air cleaner kit with spare air cleaners and adaptors

All the piping from the hot side of the motor including the 2 pipes custom painted in 2 pac black metalic

This is a entire bolt on and go set up i made 470 hp atws on this combo on 20 psi with max 10 knock on a very safe tune.The turbos seem to be in great condition and in perfect working order,Can view on the car if need be and see it running and go for a drive if your prepared to come to hervey bay to buy them.

Reason for sale is im looking at doing something diffrent from the normal.

These turbos would have to be about the best street turbos ever made they are very responsive.Look up my build up threat to see dyno sheets and power curve.

$3500.00 ono i am open to offers but please do not be silly the dump pipes and front pipe them self to buy new are not cheap,Every thing here is in perfect working order.

Happy to have the items taken off at my expense happy to pack up and send at buyers expense.

I don t see the point in posting pictures as they are low mounts in the factor position

Please feel free to send me private tells i can produce dyno sheets to show hp.

Id prefer to sell as a kit and not part out but you can always ask,But place a offer don t just ask how much i will ignore silly offers and i know what this stuff is worth as i bought it all.

Thank you for your time.

personally been in the car and experienced the response all the way through the rev range, awsome price for an awsome setup good luck man!

cheers for the bump mate

All pms returned.This stuff is already discounted and is very cheap for what it is guys.

Flexible on price yes but not that flexible haha

Keep em comming guys open your purse strings you know this gear is decent and worth every cent.

when the engine was taken out for it to be resprayed the turbos were checked & hervey bay qld 3hrs north of brissy and I can help with freight if needed :)

Edited by johnbarry88

Turbos are tip top condition.

Im located in hervey bay queensland.

As for the kms i have done maybe 2000 to 3000 ks on them in 2 years i don t drive my car much to be honest due to work commitments.

Every thing on my car is in perfect working order if its not i replace it on the spot.

As i said befor reason for selling is i want to go to a single and have already purchased a new combo.

I don t care if they don t sell to be honest,Im not hard up for money but id like to see them put to good use some where else rather then sit in my parts collection thats getting rather 2 large to be honest.

would you ship to NZ?whats the best you can do for.

Twin HKS 25/30s

Twin turbo manifolds unknown brand.

Mines sports division stainless dump pipes

only want these.

cheers

How much for just veilside front pipes? Only if you're interested in separating of course.

Pm sent mate,Just waiting on a reply he made a offer on the turbos dumps manifold.

=] I am thinking of going back to street setup. I got a full TO4z Garret Turbo Kit making around 430kW at rear. Keem to swap and exchange $$$ Turbo is like brand new Absolutely to shaft play barely done 5000 KM mainly tune in and dont drive. Are you keen? =p

Edited by GTRBOYZ

I have had offers on about every thing but also had offers on the entire kit.

Im awaiting a few private msg.

Looks like id make far more money selling the kit in bits.

Every one asks how much for this and that.You would be better off making a offer to be honest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...