Jump to content
SAU Community

Recommended Posts

rb20det parts all in perfect working order

TRUST TD06H-25G Turbo kit/stainless manifold

46mm External gate with screamer

Kit for $2500, manifold $500 turbo and gate $2000

will throw in front and dump pipe and heat shield plus speedflow braided lines

Trust Adjustable Cam Gears w/ Trust Timing Belt $500

SARD 720cc injectors $600

APEXI Power FC + Hand Controller $1500

GREDDY e-01 boost controller with LCD screen $600

Aftermarket Coilpacks $300

Rb20det motor, unknown km's. has lifter issues but still drives hard $800

all to suit rb20 and are in great working order

might have other stuff lying around, pm me or email [email protected] I will personally call all genuine inquirer's

Mitchell

Link to comment
https://www.sau.com.au/forums/topic/346377-tough-rb20-gear-for-sale/
Share on other sites

mid north coast n.s.w Port Macquarie

coilpacks are D1 there blue (i think) allready had offer for $200 but looking for a smidgen more than that, includes 6 stock coilpacks aswell for the right buyer.

  • 2 weeks later...

cam gears might be sold, there off the motor now and i have pics if this guy falls through. looks like the belt has some slight wear so i cant really guarntee it so i wont be including it in the sale now. ill let you know if old mate doesnt pay up

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...