Jump to content
SAU Community

Recommended Posts

hey for those running 19'' on there v, with 19x8.5 fronts do you have spacers on the wheel hub?

Hi mate,

Would you know what offset you getting? It's depends on the offset. Mine is 19x8.5 +5 at front and I don't need spacers as they sit very flush. I will need to roll the guards if I put spacers on and lower it.

One of my friend, xtc, had spacers on his 19 inch rims before he has 20 inch Volk GT-C. I don't know his 19 inch rims spec though.

Basically, 19x8.5 with low and negative offsets wouldn't need spacers, but higher offsets do if you want the rims to sit flush to the guards.

Good luck.

Edited by Victor.T

no idea of my offset but im running 19 x 10 on the back with no issues not sure on the fronts think they are the same or 19 x 9.5 but they come dam close to the suspension whilst allmost filling out the guard

I know that my 18 x 9.5 +20 track rims stick out a the front just a tiny bit

they are tenzo type m specs are 19x8.5 5x112/114.3 offset is +45 all around

any idea on what mm spacer i would need for fronts and rears?

Depends how close to the guards u want to b. R u lowered. My current rims are 8.5 front wid +35 offset. It sat inside the guards as soon as i dumped it on coils it sits way too inside and id need like a 38mm spacer to make it look guud again.

If u running stock height then id say a 20-25 mm spacer for the front.

I assume the rears are 9.5? in that case id say round the same.

stock 17'' size are - Front: 17"x7.5" +30mm offset and Rear: 17"x8" +33mm offset and they sit flush.

does that mean i need 15mm spacer for front and 12mm spacer for rear on the 19'' have now to sit flush?

by tyres on the 19's are 235/35 all round too ( i cant remeber the tyres on the 17's i had)

I wudnt say the stock rims sit flush bro, but to each is his own.

Best thing to do is put the wheels on and then measure and work out wat mm spacers u require based on distance to the guard.

Hope that helps

stock wheels are never flush.

people also have differing opinions on "flushness", width, offset, camber and tyre sizes will play an important part.

if you don't have camber arms, lowering your car will increase its negative camber.

you won't get anywhere near being flush with x8.5 +45, your main concern now is whether it will hit the front suspension arms. if the stock 17s are x7.5 +30, that's equivalent to x8.5 +42. so it should be fine

on a 19*8.5 +45, I'm gonna stick my neck out and say that you will need spacers especially if you have brembo brakes, but more for the aesthetic

i'm currently on 18" with 9.0 +30 fronts and they could use a 10mm spacer to sit flush (but I am running -1 camber)

hi guys just updating this thread for those keen to know what happened, i went to tempe tyres and got 30mm spacer for the front and 35mm for rears, sit perfectly now. they charged 50 a wheel which i was suprised since it was that cheap. also went to ozzy tyres they were charging 150 a wheel which i laughed at. anyways thanks for the help and answers.

hi guys just updating this thread for those keen to know what happened, i went to tempe tyres and got 30mm spacer for the front and 35mm for rears, sit perfectly now. they charged 50 a wheel which i was suprised since it was that cheap. also went to ozzy tyres they were charging 150 a wheel which i laughed at. anyways thanks for the help and answers.

FYI did you get slip on spacers or bolt on ones? The latter are more expensive and safer. Either way they are both illegal. Your insurance will be void if u happen to be involved in an accident and they find out u have spacers.

Food for thought.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...