Jump to content
SAU Community

Recommended Posts

hey all have a few bits of gear for sale

180sx vertex rear bar, in very good condition $100

010120081158.jpg

010120081157.jpg

010120081156.jpg

what i believe to be s14 rear bar?? im not 100% sure what it is, it sort of fits on an s13 but hangs bulk low so makes me think its from s14 some damage in corner easy to repair $80

010120081162.jpg

010120081163.jpg

010120081164.jpg

what i believe to be r32 side skirts actual bomex brand the sticker is set into the glass some damage not hard to fix tho $80

010120081159.jpg

010120081161.jpg

s13 climate control unit $20

010120081165.jpg

s13/180 fan shroud $50

010120081166.jpg

010120081167.jpg

sr viscus fan $40

010120081175.jpg

3x hks 2.7in joiners $20

010120081178.jpg

2x gtr intercooler pipe joiners $20

010120081179.jpg

bride low low drivers seat rail, have custom rail in car so not needed $200

010120081171.jpg

010120081172.jpg

010120081173.jpg

010120081174.jpg

sr afm $40

010120081177.jpg

s13/180 air con vents $10 each

010120081176.jpg

sr20 cold side coolerpipe with turbosmart vee port bov fitted, all welded on propely $100

010120081168.jpg

010120081169.jpg

010120081170.jpg

rb20, 25 cold intercoolerpipe, goes from guard to factory pipe infront of the engine $50

010120081180.jpg

010120081181.jpg

will swap plus cash whatever way depending, for s13 vertex rear bar, s13 roof spoiler, 4 point harness etc

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...