Jump to content
SAU Community

Whiteline Bushes - Kca332 And Kca347

xRHETTx
 Share

Recommended Posts

xRHETTx Mentor

xRHETTx

Posted
Posted

Hi all,

I have a 2 sets of Whiteline bushes for sale.

1 set are KCA 332 which are the adjustable front radius rod arm bushes, used for adjusting caster these suit a variety of cars including R32 GTR, R33 GTR and Stagea C34 RS4, but please check on the whiteline web site for a full list.

1 set are KCA 347 which are the adjustable upper control arm bushes, used for adjusting camber, these suit a variety of cars including R32 GTR, R33 GTR and Stagea C34 RS4, but again please check on the whiteline web site for a full list.

They are both brand new, paid a lot of money for them from Pedders ($145 and $160). I have opened the KCA332s but didnt end up fitting them. Selling as I am moving overseas and my car will be living with my mum for a while, so I dont think she will appreciate them.

Asking for $120 for each, or $200 if you buy both.

Pickup is available from Armadale 3143, Victoria. Or else will post Australia-wide $10 per item or $15 if you buy both.

Please PM, reply in the thread or call or text me on 0404021495.

post-1218-0-35168900-1292056648_thumb.jpg

post-1218-0-16916900-1292056827_thumb.jpg

Regards,

Rhett

Link to comment
https://www.sau.com.au/forums/topic/347226-whiteline-bushes-kca332-and-kca347/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...