Jump to content
SAU Community

Recommended Posts

Hi guys,

I am selling my RB20DET T3 that i bought, as i no longer hav the funds to build the motor i was going to get done.

So here goes, details are:

Specs-

Nissan 16V10 T3

-Ceramic Turbine

-Water & Oil Cooled

-Chrome compressor housing

Can handle upto 1 Bar (14.7PSi) of boost

Great for bolt on modifications

________________________________________________

Sizes (Approx)-

60mm Compressor Wheel Trim

50mm Air Intake Diameter

60mm Turbine Wheel Trim

40mm Turbine Exhaust Diameter

________________________________________________

History-

I bought this turbo for my RB30ET in my vl as a project.

Its from a R32 RB20DET Gts-T Skyline.

After dismantling and cleaning out the COMPLETE turbo, the compressor housing was professionally chromed (worth $100+) to help dissipate heat and for the impressive finish =D

Unit has very little shaft play. As you can see the shaft is clean and strong

No cracks in the turbocharger what so ever.

(Wastegate actuator removed for picture purposes only)

________________________________________________

Turbo & Wastegate Actuator only. Sold As is.

Turbo is in excellent condition and will look great in any engine bay.

chasing $300 firm, must sell ASAP, please no time wasters

Melbourne/Geelong buyers only

Link to comment
https://www.sau.com.au/forums/topic/34742-for-sale-chromed-t3-rb20det/
Share on other sites

come on guys i payed 500 for this and in the last 2 months its been sitting in my room and ive not used it once, so in other words im willing to loose 150 for it. ask around these r still selling for about the 450 mark.

BARGAIN

bump. and also if u r wondering its the ball bearing type. come on guys this is an excellent turbo and cheap too. i posted it up on here to give u skyline enthusiasts a chance as i also tryed selling it on calaisturbo.com with no luck cos it would be more work to fit it onto an rb30 than its worth.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...