Jump to content
SAU Community

Recommended Posts

you'd want to tap into the sump wouldnt you?

because there wouldnt be any oil in the pump until the car is cranked/running?

but it would suck from the same place (oil pick up) and put back in the pressure side to go to the oil filter . it wouldn't be able to suck thro the standard oil pump because of the gears ?

Link to comment
https://www.sau.com.au/forums/topic/348646-rb26-oil-pump/#findComment-5604820
Share on other sites

whats the point of doing it. its not like engines have ever had an issue with starting on a normal oil pump before.

more for the fact that if your standard pump shit it self you have some chance of saving the motor

Link to comment
https://www.sau.com.au/forums/topic/348646-rb26-oil-pump/#findComment-5604965
Share on other sites

yeah ok fair point, im not sure that you would have enough power in the electric pump to supply the oil

yeah im with this, if you need something large to get the oil round in the first place, i dont think a small 12v pump would help much,

be better off with a good oil pump (nitto or jap brands), or external wet setup.

Would be better off to use a pressure switch for an engine cut, by time the small pump kicks in the damage would be done

Link to comment
https://www.sau.com.au/forums/topic/348646-rb26-oil-pump/#findComment-5605205
Share on other sites

yeah ok fair point, im not sure that you would have enough power in the electric pump to supply the oil

http://www.turbowerx.com/Scavenge_Pumps/Exa-Pump/Exa-Pump.html

check this pump out

they reakon it can pump 100 psi and comes with a 2 year warranty

Link to comment
https://www.sau.com.au/forums/topic/348646-rb26-oil-pump/#findComment-5605514
Share on other sites

For the money you'd spend on the pump, modifications, hoses, and fittings, you may as well have bought a jun/nitto pump anyway. Engine alarms and kill switches are the go to prevent engine death in the event of oil pressure loss, or accumulators if you want to protect against oil pressure surge as well.

Link to comment
https://www.sau.com.au/forums/topic/348646-rb26-oil-pump/#findComment-5605551
Share on other sites

yeah, just buy a decent pump and a warning, in a built engine with crankcollar, and nitto/jap pump they can handle 9000rpm+ launchs without breaking.

seems more of a waste of effort and money to do it with a standard pump.

get the accumulator, but like mentioned in the other thread and on the site, those setups are for big hp and serious race cars

Edited by jangles
Link to comment
https://www.sau.com.au/forums/topic/348646-rb26-oil-pump/#findComment-5606157
Share on other sites

I wouldn't bother farting around with the oil pump... If you wanted to add an electric pump, you would install it as a redundant/seperate system.... with it's own oil pick up, filter and feed into the oil galleries.

I'm just going to use the largest accumulator or 'accusump' I can fit, along with a good oil pump and oil pump drive.

J.

Link to comment
https://www.sau.com.au/forums/topic/348646-rb26-oil-pump/#findComment-5607051
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...