Jump to content
SAU Community

Recommended Posts

Seeking interest in buyers for my R34 Tiptronic gearbox which has had the full works kit by MV Autos. Kevlar bits, new servos, shift kit, valve body, high stall convertor and a custom steel flex plate (as we destroyed the stock r34 flex plate with big power).

The box has withstood 300rwkw+ for about 5000km, previously withstood 250rwkw no troubles. Auto has been serviced with Castrol Transmax regularly and has had a B&M trans cooler on it with temp gauge. Always been cooled down when taken up near 100 degrees.

Shifts nice and hard into 2nd and 3rd. Locks up well and the high stall is great for getting onto boost nice and early.

You'll get the box itself, B&M trans cooler & lines, half tailshaft, MV high stall convertor, MV steel flexplate.

After $1500 or swap for R33/R34 5 speed with half tailshaft. Must be in good condition.

Box still in car, can take you for a drive to show its in good working order.

Pickup Northern Beaches Sydney, or I can deliver in Sydney metro for a small fee.

Edited by Mitch_Rona

Hey there,

im interested in your box, will it fit into an R32 by any chance? what sort of shifter were u using with it? will the gearbox controller come with it also?

thanks

Matt

Hey there,

im interested in your box, will it fit into an R32 by any chance? what sort of shifter were u using with it? will the gearbox controller come with it also?

thanks

Matt

PM replied

Very interested in this - just what I'm after...shame you're not in Brisbane :-(

I can pop it onto a pallet and send it up to Brisbane. Want me to get a quote?

I can pop it onto a pallet and send it up to Brisbane. Want me to get a quote?

I could organise that side of things as I have a few contacts...

depending on how flexible on that price, I would be keen for sure :thumbsup:

I could organise that side of things as I have a few contacts...

depending on how flexible on that price, I would be keen for sure :thumbsup:

No worries. I can get it on a pallet and fork it onto a truck if that helps.

Can move slightly on the price if it means a quick sale. :)

  • 2 weeks later...

Still available. Someone surely must want a tough 34 auto box? Built to take serious power.

I do! :yes:

Haven't forgot, just need to suss a few things out first ;-)

  • 3 weeks later...
  • 2 months later...
  • 3 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...