Jump to content
SAU Community

Recommended Posts

I have an R34 GTR Cooler for Sale in Very Good condition. It has the sensor hole at the back to prove its from an R34 GTR.

$550

Great upgrade for GTST!

R34BGTRa.jpg

Pic is not of actual cooler but is very similar to the pick

Need to sell ASAP

Avaliable for pick up from Moorabbin immediately

email: [email protected]

or SMS 0413 942 864 business hours, call after hours

Link to comment
https://www.sau.com.au/forums/topic/35039-r34-gtr-cooler-for-quick-sale-vic/
Share on other sites

Hey buddy I orginally bought piping & cooler off someone else in this forum, however the piping and the cooler do not match up properly and at the time i had fitted the new turbo and it was booked in for a tune, so i had to have an intercooler on it. As this cooler & piping did not match up i was forced to buy a new HKS cooler kit from UPI on the spot so now i need to sell the cooler & piping that i bought.. but now sell them seperately as they do not match up.. the piping is sold so now just the R34 GTR cooler, this can be polished up also for around $30.

Power wise, R34 coolers are good for around 300rwkw..

From stock GTSt if you had say exhaust/filters/boost 10psi id say you would make around 165-170rwkw, with the cooler you would easily increase up to 180-190 and be able to run 12-13psi more safely

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...