Jump to content
SAU Community

Power FC Tunners

Gdup

By Gdup,
in General Automotive Discussion

 Share

Recommended Posts

GZ R33 Community Regular

GZ R33

Posted
Posted
Does any1 know of C and V performance? Are they good at tunning, especially tunning the FC?

Does anyone recommend? If not, who else do you reccommend? Also i am in sydney.

Cheer All

Apparently Croydon are the only ones in Australia that have the software, all others tune off hand controller. (With software there is at least 30kw more)

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-702523
Share on other sites
Gdup Apprentice

Gdup

Posted
  • Author
Posted

But wouldnt using the hand commander be better? because you are using the FC's own tunning product? Im using CRD developed thier own program because they were tunning the FC's before the hand commander came out.

Apparently Croydon are the only ones in Australia that have the software, all others tune off hand controller. (With software there is at least 30kw more)

If this is true, then wouldnt everyone go to CRD?

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-702988
Share on other sites
Jimbo2000 Grand Master

Jimbo2000

Posted
Posted
But wouldnt using the hand commander be better? because you are using the FC's own tunning product? Im using CRD developed thier own program because they were tunning the FC's before the hand commander came out.

 

If this is true, then wouldnt everyone go to CRD?

as far as i know the PFC HC has been available with the FC since it was invented.

the laptop software allows them to tune in 300 units instead of the 60 units that the HC allows (not the right figures but you get the point)

i would also guess that the laptop software will not guarentee any extra power just easier tunability thus more can be done a lot easier and quicker.

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-703242
Share on other sites
B-Man Grand Master

B-Man

Posted
Posted

Bullshit about the laptop software for PFC - A good tuner can get the same result but it will take longer. The HC is awkward and lots of writing on paper. But if they know what they are doing , not having the Datalogic whateva is not entirely neccessary.

My 0.2c

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-703269
Share on other sites
Jimbo2000 Grand Master

Jimbo2000

Posted
Posted
Bullshit about the laptop software for PFC - A good tuner can get the same result but it will take longer. The HC is awkward and lots of writing on paper. But if they know what they are doing , not having the Datalogic whateva is not entirely neccessary.

 

My 0.2c

Correct

Link to comment
https://www.sau.com.au/forums/topic/35160-power-fc-tunners/#findComment-703598
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...