Jump to content
SAU Community

Fs: Garrett Gt3076R

NissTrust
 Share

Recommended Posts

NissTrust Enthusiast

NissTrust

Posted
Posted

Hey Guys, i have a GCG Custom GT3076R Stock Location Turbo for a WRX ie, any applicable EJ20/25 setup

Internal WG

1Bar Actuator

Compressor 0.6A/R

8cm2 Hotside

CHRA: 700177-7

Compressor:

ind 57.0mm

exd 76.2mm

trim 56

A/R 0.6

Part number: WRX-XTR-450

Call GCG with this part number to verify CHRA if you like.

Purchased 2 months ago and have not installed it yet.

Looking for $1000

it's done 22k km was fitted to gc8 2lt and only ran 14psi through it so 'never used' it to it's potential.

Postage at buyers expense.

Located in SE Melb burbs

5331637550_a9e9d68bda_z.jpg

Compressor Map

700382-1&2&3comp_t.jpg

http://www.turbobygarrett.com/turbobygarrett/catelog/Turbochargers/GT30/GT3076R_700382_12.htm

Link to comment
https://www.sau.com.au/forums/topic/351976-fs-garrett-gt3076r/
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Have you flushed the initial fluid yet? It should look like a rainbow unicorn shat glitter into it. 2nd or 3rd fluid change is when you party.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • PranK
      Most women will agree that parking is the most taxing part of driving

      By PranK · Posted

      Go back and watch the video again... 
    • funkymonkey
      Most women will agree that parking is the most taxing part of driving

      By funkymonkey · Posted

      Are you meant to double fist them?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
×
×
  • Create New...