Jump to content
SAU Community

Recommended Posts

I have decided to part with the 31. First to go is the Rb25

engine009.jpg

RB25kas016.jpg

Engine is assembled with race series forged pistons 50thou over.

HKS cams 9mm Lift 264 duration on the exhaust, Inlet has 8.8 mm 256 duration retaining the VCT.

HKS Cam sprocket on the exhaust.

Eagle rod's

MLS Metal head gasket

1mm oversized valve

Upgraded valve springs

race series bearing's, large ends and mains.

all welsh plugs replaced

all heater hoses replaced

Bottom end was balanced including the Jim Berry clutch.

Split fire coil packs

N1 water pump

N1 oil Pump

Crank collar

Standard turbo

HKS dump pipe

Engine has done roughly 10,000km's since being built and is still in vehicle to be viewed.

Motul 300v comp oil has only been used after the initial run in period.

Loom can be supplied with engine but it will suit a 31 conversion.

Once buyer has paid deposit/full amount engine will be removed and buyer can collect from Glendale N.S.W

Engine is listed for sale else where.

Asking $7000

Any info call Kyle 0417224107

Link to comment
https://www.sau.com.au/forums/topic/352294-rb25-forged-engine/
Share on other sites

  • 1 month later...
  • 2 weeks later...
  • 2 months later...
  • 1 month later...
  • 2 weeks later...

I have decided to part with the 31. First to go is the Rb25

engine009.jpg

RB25kas016.jpg

Engine is assembled with race series forged pistons 20thou over.

HKS cams 9mm Lift 264 duration on the exhaust, Inlet has 8.8 mm 256 duration retaining the VCT.

HKS Cam sprocket on the exhaust.

Eagle rod's

MLS Metal head gasket

1mm oversized valve

Upgraded valve springs

race series bearing's, large ends and mains.

all welsh plugs replaced

all heater hoses replaced

Bottom end was balanced including the Jim Berry clutch.

Split fire coil packs

N1 water pump

N1 oil Pump

Crank collar

Standard turbo

HKS dump pipe

Engine has done roughly 20,000km's since being built and is still in vehicle to be viewed.

Motul 300v comp oil has only been used after the initial run in period.

Loom can be supplied with engine but it will suit a 31 conversion.

Once buyer has paid deposit/full amount engine will be removed and buyer can collect from Glendale N.S.W

Engine is listed for sale else where.

Asking $7000

Any info call Kyle 0417224107

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
×
×
  • Create New...