Jump to content
SAU Community

***r32 Sale/swap***

slidnreds13
 Share

Recommended Posts

slidnreds13 Rising Star

slidnreds13

Posted
Posted

Ok its come time for me to sell my pride am joy to fund my new project

Ive had this car since february this year, i can honestly say ive never had a problem with this car, its reliable as all hell and i used to drive to nourlunga everyday for tafe so the last 10,000 kms are pretty much highway driving and it gets serviced every 5000ish.

Only problem ive had is i snapped the belt that runs the waterpump, watched the temp go up a little an pulled over an diagnosed it straight away. happened almost a year ago an its never overheated since! even on those 40 degree days driving to adelaide

1990 M-spec R32

Black

Factory 5 speed manual RB20DET

145xxxkms

Cyclone alarm system

Rego included till Feb 2011

Asking price is $9,250 ono Or swaps for r32 4 door shell with or without engine or something of interest.

Cheaper without the wheels

Cheaper without boost controller

Exterior:

Type M kit all round

HID lights

Brake calipers painted with duplicolour (adds atleast 20 Rwkw)

Interior:

Clean as f**k dash no cracks etc one bubble

Standard front and rear seats

Standard wheel in average condition

HDI duel stage EBC with boost guage in drivers side air con vent

Turbo timer

Custom gear knob

Brand new gear and hand brake boots

Digital climate control

Genuine skyline floor mats

Fire extinguisher in glove box (can never be to careful)

Air conditioning retro fitted and regassed a few months ago!

Full Alarm system, remote central locking, knock sensor(very sensitive) Remote engine start (not currently installed) And all the other anti hi-jacking crap

Stereo:

Kenwood head unit MP3, aux Etc

6x9s in the rear

Front splits with tweeters

12" Sub

1000w amp powering it all

Engine:

Internally standard RB20DET with 145xxxkms, compression test done a couple of months back and got 140 +-5 accross the board

RB25 turbo (OP6) with 5x,xxx kms on it

Rebuilt gearbox, all bearings replaced and 4th gear detents

3inch single piece dump pipe to high flow cat

3.5inch straight through exhaust with nice cannon (not too big) But sounds tuff!

ISC front mount intercooler kit

Extreme heavy duty cushion button clutch (i think)

ISC 52mm twin core radiator

Blitz pod filter

Shoes and suspension:

Work Emotion Cr Kais freshly powdercoated white so not a scratch on them!

F18x8.5 235/40/18 R18x9.5 265x35x18 nangkang ultras

Blue Rays lock nuts

Standard suspension, drivers side rear sits a tiny bit lower so may need replacing but doesnt make any noise or make a difference.

Other things you should know:

Interior is mint bar the rear side panels and bubble in the dash

Passed regency no worries 12ish months ago

All new bushes throughout the car

I have tried my best to remember everything but theres probably some things ive missed.

ANY mechanical check is welcomed as long as i dont have to leave my car anywhere (as its my daily) and as long as it doesnt cost me. as i said it will be on the dyno this week so ill see if there are any problems and get a power reading.

UPDATE: Pulled just under 160kws on the dyno @ 9psi with no boost controller. Guy from jazmac couldnt believe how healthy the engine is!!

Boost controller set for low boost= 10psi at around 165ish kws and high boost= 14psi at around 190ish kws (may even crack 200) will get it on the dyno again if i get time.

post-69945-0-26314900-1296648295_thumb.jpg

post-69945-0-27175700-1296648307_thumb.jpg

post-69945-0-89292600-1296648336_thumb.jpg

post-69945-0-45244300-1296648347_thumb.jpg

post-69945-0-40605600-1296648357_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/352614-r32-saleswap/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...