Jump to content
SAU Community

Recommended Posts

R34 GTR Vspec - Second owner in Aus, imported at 63000kms, Bayside Blue

106,xxx kms on body, 3xxx kms on new engine

Genuine nismo front bar

nismo z-tune side skirts

nismo z-tune rear pods

Front underbody diffuser

Rear Carbon Fibre underbody diffuser

Genuine Nismo cat back exhaust

Genuine Nismo front pipe

Apexi twin pod intake kit

Apexi RSM Black edition

Apexi AVC-R Black edition

Apexi PowerFC + Hand controller

Pet Turbo Timer

Koyo Radiator

Te37 SL 18x11 +18 with Kumho Ecsta KU31 295/30/18, all with 90% tread

Project Mu HC+ front and rear brake pads (6000km on them so far only)

Cusco Zero 2E coilovers (comfy but firm)

Fumoto sump plug valve

20% tinted windows all round

7" multimedia touchscreen with dvd, tv, ipod, bluetooth, reverse camera, aux, GPS with 2009 maps for all of Aus

Nismo MFD Upgrade

Genuine V-spec 2 alloy pedals

Genuine GTR Floor mats front and back

Engine built by Status Tuning

JE forged pistons, rods, crankshaft

ARP stud and head bolts

Exedy Heavy Duty clutch

Exedy Lightweight Flywheel

Gates Timing Belt

N1 Oil pump

N1 Water pump

2 x Garrett 2560-7 turbo's

Serviced at IS Motor Racing with Royal purple engine oil and oem oil filter at 105,000kms.

Looking for $49,000 ono or willing to part out to reduce price. Located in, Sydney, NSW

For more information and contact details send me a PM or make a post.

Cheers

Dave

5401212738_8c4a6ac1df_b.jpg

DSC_0431.jpg

img9051e.jpg

img9053j.jpg

Edited by jnxr
Link to comment
https://www.sau.com.au/forums/topic/353474-fs-r34-gtr-99-bayside-blue/
Share on other sites

  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...