Jump to content
SAU Community

660Cc Injectors To Suit Rb26

Brezza
 Share

Recommended Posts

Brezza Proficient

Brezza

Posted
Posted

660cc Injectors to suit RB26 fuel rail

Rochester Type injectors.

Cost me $660 to buy and $100 to modify to suit rail.

Will sell for $500

Ran these in my GTR for 1 year, only changed them for 1000cc injectors for e85

Good injectors, never had any dramas with them.

Pulled some good power with them. Perfect for a GTR wanting to get in the 300+kw range on PULP

Had these running on my GTR @ 18psi with STD AFM's and got 320rwkw

then when i upgraded to Nismo AFMS' i ran 22psi and got 350rwkw

Still had headroom for more power

PM me

Located in Glenelg, SA

Willing to post for extra

Link to comment
https://www.sau.com.au/forums/topic/354893-660cc-injectors-to-suit-rb26/
Share on other sites
  • 3 weeks later...
  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      HR34 GT speedo issue

      By joshuaho96 · Posted

      Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Dylannn
      WTB RB25 Gearbox NSW / central west

      By Dylannn · Posted

      Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      He means "as opposed to mechanical cable drive". Older cars (R32 for ex.) had cable drive. Later cars with essentially the same gearbox, ie R34 GT (NA RB25) used essentially the same box as the R32 GTSt, but instead of a cable drive, had an electronic speed sender plugged into the same hole in the box, running from the same little gear that would have run the cable. Some of the shittier later cars use a speed sender on the nose of the diff, or the ABS sensors.
    • GTSBoy
      Hypergear Turbochargers and High flow Services Development thread

      By GTSBoy · Posted

      Lower than engine, or lower than it should at the hubs? Either way, that is a nice power figure and I'm not surprised you say it rips now. What stopped you from turning it up any more? Injectors? Or did it just stop responding to boost?
×
×
  • Create New...