Jump to content
SAU Community

Recommended Posts

13.8 - 14.4 is ideal. little under is ok but 12.6 is too low. is that the best you get out of it or does it get better with rpm? were any accesories being run like lights or stereo? when you stop the engine and just have the key on what is the voltage? need to ensure that gauge is reading correctly first then go from there.

  • Like 1

Test it from the battery - in my experience, the MFD reads slightly low (though, even then seems even lower than I'd expect)

Edit: Just went and checked my MFD - reads 14.1V at idle (and 14.3V directly at the battery) - weird - seem to remember it being out by more (i thought 1V) when I first checked ..

Anyway - hopefully that helps; definitely sounds like you have dramas with your alternator if that's the voltage whilst idling/driving...

  • Like 1

No lights or stereo being run, without the engine running voltage is 12.4....Same readings from battery give or take .1... Took it to mechanics said the alternator is running and charging ok :dry: but its down near 12 and should be up near 14

No lights or stereo being run, without the engine running voltage is 12.4....Same readings from battery give or take .1... Took it to mechanics said the alternator is running and charging ok :dry: but its down near 12 and should be up near 14

hope u didnt pay him for that advice.. better off taking it to an auto elec, alternator might be on its way out

there is a chance the alternator is ok but the wiring is the problem. check the voltage at the alternator (although i have a feeling that if the earth to the alternator is dicky then it will lower the voltage reading you get there too).

ok im an auto elec...battery volts should be 13.8 - 14.4 with the revs up so the alternator is wroking harder and charging, gauge is always going to get lower as remember there will be a drop is volts in the leads, test the battery with a multimeter and also at the alternator there will be a differents onces again in the cable....if a alternator/ battery is lower then 13.4 running id be getting the alternator rebuild dont go out and buy one cheaper to fix urs

what do u mean how does it cost, to pull one down, clean, sand blast, replace bearing, and any other parts to make it new is cheaper the buying one,

we charge $132 plus parts, take half a day or so to do,

132 for half day is cheap :whistling:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...