Jump to content
SAU Community

Recommended Posts

hello' yes problem is it runs 1000rpm.and connot,no mater what i do get it below 20 degrees timing? any ideas anyone. thanks. .

.

)its also cutting out over 12psi boost. tryed stock ecu and another that sopose to be mapped for higher boost,and cuts taken off. but but ecu's seem to run the same

.have t04,but shouldnt be that causeing probs with to much air.(

front mount

greedy intake

t04

38mm wastegate

3'' way throught

pod

manual.--- - with auto ecu-and manual mapped ecu--have mapped 1 in now.

bleeder

fuel reg

thats bout it i think for mods

  • Nope 1

You need to get the idle correct. There should be a tutorial somewhere on how to adjust it using the screw in the AAC valve.

Then make sure that the timing light you are using is not doubling the reading when you are checking base timing. Best to go "old school" by inserting a spark plug lead between #1 coil and #1 spark plug, then measure the timing off the lead.

the AAC valve screw is right in.. if i wind it out a little it revs to 1500rpm. .no mater if i turn cas.it stays on 20'. ...could cas be a tooth out??? i can put the timing on -15 in an active test.from conzult or somthing sounds right. but as i carnt burn it to ecu. it jumps back to 20. in saying that. when on -15. the conzult reads 10 degrees. some say auto motors came out running 20 degrees, but shouldnt mean i carnt get it to 15 somhow

Are you sure there are no air leaks anywhere?

+1

Intake manifold/plenum/throttle body gasket, vacuum line off/leaking, dud brake booster etc..

If not:

-A scantool will help (ie check what the IAC is doing, if the car's staying on cold start and holding the idle too high)

-Check your throttle body isn't jammed/being help open.

-Dodgy MAF?

Are you sure there are no air leaks anywhere?--)--------- yeah to me that sounds the prob,i will check today.

Intake manifold/plenum/throttle body gasket, vacuum line off/leaking, dud brake booster etc..--)----------------------------- will do proper check today.

-A scantool will help (ie check what the IAC is doing, if the car's staying on cold start and holding the idle too high--)-------------------------------what is IAC sopose to be reading at idle ??i have a scantool..

-Check your throttle body isn't jammed/being help open.--)----------------------------------------------will also check that today.

-Dodgy MAF?--)----------------------------could most likely be-it was throwing maf connection code, and makeing motor just stop random. till i earthed the E to the chassis hasnt really done it since, but still could be stuffed..

thanks guys appreiate th help ill give them a go and see what happens. also have nistune but no ECU yet. is there somthing in the program to look for tht might help,such as levels of sensors, everthing should be basicly stock.

ok i think ive sorted air leek found 1 round addaptor plate to throttlebody, prob now is it cuts out on boost random boost levels. i will try mates coils, but any ideas way it would cut at low boosts and motor surges when pulling up,like geting way to much fuel.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Will have a look at that. I cant see any leaks 
    • Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
    • Hi Everyone I am from West Pennant Hills in NSW. Been too busy until recently to attend to my RB25DET Series 2 engine until recently. I am planning to stick it into the S15 shell at this stage, unless a nice SR20DET turns up... For now, i am going to try and get the RB25 running and working well then decide what gearbox to use. My preference is to retain the SR20DET  6 speed gearbox and tail shaft to retain as much and least modifications as i can avoid. I am an old guy and won't be doing any heavy drifting so i don't need a bullet proof gearbox Does anyone have experience with starting the RB on a stand? I got everything setup as much as I can with the info i can find... endless searching and videos on Youtube I would be great to get some pointers Cheers Songo
    • Hey all, Recently have had my s1 r33 gtr serviced and noticed my coolant reservoir was topped up to the max line. Took the car out for 1 yesterday and noticed today the reservoir is completely empty.  Any ideas? Radiator is full
×
×
  • Create New...