Jump to content
SAU Community

Recommended Posts

Put some decent plugs in and get some yellow jackets.

If you're getting misfire, a popping sound, on high boost then that's almost certainly the problem. Gutsy trying the holden coils, but yellow jackets are only round $400, have 2 years warranty, and have been proven to be pretty effective

Had to get the car towed. It will idle, but not be put under load or it will want to backfire and stall... I cant see me doing anything other than rolling in idle in it.

Will try putting standard coilpacks in during the week again, but I'm sure it's something else.... is a vacuum leak going to be so severe to make it not even idle or be able to do 10km/h? I searched the piping for leaks, maybe I should pressure test it somehow.

running a wasted spark set-up would be fine if you had a after market ecu to control the dwell time on the coils/ igniter. too much dwell and the igniter will get red hot and prematurely fail, too little dwell and the misfires and running like crap are your friend, a wise person once told me ;)

This man speaks truth.

Sounds like your result is even worse than i had when i went with bosch coils before split fires were cheap and china gear arrived.

I could at least drive around at less than 7psi and have very smooth idle and light load running. Went to shit at anything near 1/2 throttle.

Your plugs are fouled because it doesn't have a big enough spark to properly burn the fuel in the cylinders.

The weird thing is that it is throwing a fat spark.... and the car won't even idle with the standard setup back on it now. I know I'm going to spend like $500 on coilpacks and loom and end up in the same spot. However I guess I have a spare AFM and igniter now if anything goes wrong in the future.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...