Jump to content
SAU Community

Recommended Posts

$36,000

Maybe intrested in swaps + cash

Fresh engine 2 events since rebuild aprox 5,000km

Car currently running 365awkw with over 1400nm toque

Current tune is for mid range power delivery will make 400kw on power tune.

Everything has been done that needs to be done and all parts are basically new or are new!

Car has current 3 months SA rego

Comes with lots spares and std parts like std exhaust system.

Car as been modified from standard by myself and I have been the first owner of the car in Australia.

Top competitor in legend of the lakes hill climb also took out the overall dyno challenge at autofest 2010 Mount Gambier.

Car has barley been driven since build and is going to waist. Car was built on the basis of doing hill climbs and some track work but never seen a track yet.

Engine

Arp main bolt’s

Arp head studs

Arp rod bolts

Tomei Metal head gasket

Tomei Metal intake gaskets

Tomei Metal exhaust gaskets

ATi 1000hp balancer

Trust Oil pump

Tomei oil restrictor

Eagle rods

CP pistons

ACL race bearing throughout

Trust sump

Gready under drive pullys

N1 water pump

Nismo thermo stat

SARD 800cc

Head ported and polished

Tomei poncams B

Tomei pro double valve springs

Tomei titanium valve retainers

Nismo fuel regulator

Silicon high temp water hose set

HKS twin spark ignition

Gready solid radiator hoses

Gready oil cooler/ filter relocation

Custom hard piping kit intake/cooler

CoolingPro Intercooler

Blitz dual bovs

Twin Z32 Air flow meters

PFC Pro version with launch control and ignition cut

Braided turbo oil and water lines

Yellow jackets coil packs

HKS cam gears

OBX split dumps

Std turbo manifolds with major porting

Garret -5 turbos

kokamoto race twin 3" pipes tuned length from dumps back

justjap circuit oil catch can into a secondary custom catch can

Apexi air filters

Custom 3 core alloy radiator

Custom sure tank with bosh 044

Drivetrain

Nismo Engine mounts

Nismo Gearbox mounts

custom cusco 30mm swaybars

project D rear cradle solid bushes

project D steering rack bushes

Twin place ORC 702 clutch

Nismo short shifter

Rear adj upper camber arms

Upper front adj camber arms

Hardline caster rods

Hicas lock out bar

Front Two peice slotted rotors

Slotted rear rotors

Yellow stuff pads all round

Project mu drift handbrake pads

Braded brake lines all round

Cusco brake stopper

Tein coilovers with full in cab control

Rear LSD shimmed

Interior

6 point molly bolt in cage with full padding wrap

Nismo 320 dash

Nismo Gear knob

Fire extinguisher

Quick release steering wheel hub

Momo race wheel

Defi Gauges Oil temp/ Water temp/ Boost bar

Led shift light

Greedy turbo timer

Profec b boost controller

Exteriour

Front Bar on speed clips for quick removal

Top secret carbon rear defuzer

Top secret front add on lip

F1 carbon mirrors

BeeR carbon rear spoiler

Top secret carbon bonnet

Top secret front splitter

Tomei headlight air duct

Zigen 18x9.5 rims on 265x35x18 semi slicks advans A048

I am located in Melbourne and car is currently here.

I have driven the car a total of about 5 times this year and has always been garaged under a cover.

Engine was built a year ago by Protek Automotive in Preston and last tune was done 3 months ago with a new HKS twin spark system.

Also this is a ser3 r33 gtr so it has the extra bits std,

tuffer gearbox

xeon headlight

red interiour inserts

dark carbon instumental pannels

n1 front bar intakes

this was the last year they where made 1998

call or msg 0416250596

Also Have the following RAYS NISMO rims 18x10 at an exta cost can be neg on finally price.

The car when it was std.

post-51272-0-15188300-1300087760_thumb.jpg

Ready to drive home or straight to the track heaps of goodies and heaps of realiable all day power.

tuned on BP98

Perfect time to buy as the Aus world time attack entrys come out!

Ready to race just jump in and go!

Decided to drop the price as I have a business deal that needs some money invested into it.

So $32,000 for a quick sale!

will be taking the car to the sau vic dyno day this weekend so if your intrested come down and check it out.

Has to go guys

Didnt make down to the SAU Dyno day got held up at PRO Flows dyno day.

Car ran in 2wd and made 402.7rwkw will post up dyno sheet soon.

dont know why no-one is interested? massive budget spend, massive brand name parts list?

worried about getting it rego'd in vic? i just about all the std parts to do it?

have std bonnet change that,

have std wing blade change that,

have full std exhaust system so change that,

have std ecu and afm's change that,

remove the bolt in cage,

get rwc and your done put it all back on?

If you from SA its right to go and drive it home!

Im really interested in a e46 M3 so looking for a swap or a nice s15 with leather + cash.

Edited by Travis Trayhern

http://www.fullboost.com.au/video.php?id=613&startRow=0&endRow=10&page=1

Second car in the video.

not the most powerfull car there but it is a circuit car not a drag cal like all of them.

  • 3 weeks later...

still up for sale, car just sitting at protek over in preston feel free to go check it out and ask them about it and its build :)

interstate buyers welcome also if you need to fly in im happy to pick you up from the airport and show you the car, if you want to drive it home will throw in a free set of earmuffs haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...