Jump to content
SAU Community

Wrecking Jzx100 '96

hassassin
 Share

Recommended Posts

hassassin Newbie

hassassin

Posted
Posted (edited)

Wrecking my JZX100 '96 DARK GREEN.. PLS TXT 0423 739 643

1JZ-GTE - 98,000 k'z

Recently changed Radiator but still needs 100k service.

Custom Aftermarket Dump

HDi Hi/Lo boost controler

Series 2 Steering wheel

Greedy LS SPEC I/C

other than the above it has been reverted to stock

boots not in the best of condition but you get what you pay for

other acc and stuff for sale such as wheels etc

3K quick sale

photo-1.png

photo1.png

she did look good

photo.jpg

19" JAP Chrome Wheels - $1750+ 16 inch stockies - they have fresh front rubbers, back still have PLENTY of tread

VENERDI HEREBORRANI CL-105 VIP Wheels --- Information: FRONT 19x8.5 +35 REAR, 9.5 +38 :Perfect fit on a Toyota sedan, Chaser, Crown, Celcior, Soarer etc not sure on Nissan, please check width/offsets...

Khumos 235's on front and back with great tread, front right wheel may have a slight buckle. i paid 2 K without tyres. Original Vernadi's have gone for +4K

DSC01137.jpg

dpcopy.jpg

Tein CS Spec Coilovers - $600ono !!!

IMG_0142.jpg

Baller Grade, Pleather seatcovers jzx100 specific - $500ono

DSC01106.jpg

DSC01109.jpg

Edited by hassassin
Link to comment
https://www.sau.com.au/forums/topic/358411-wrecking-jzx100-96/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...