Jump to content
SAU Community

Recommended Posts

Greetings

I have had a scout though the threads but can't find what I am looking for.

I live around 250k from Suzuka and will be going around once a month this year with some other locals from our workshop.

I want to run Direzza 03G H (hard) compound rather than R compound (medium) as track is far away and want them to last a bit

Questions are as I have to drive to the track and back on them (have street rims with Direzza 101's for street use.) whats the best track pressure and transit pressure for these tyres.

We do 30min x 3 sessions.

I was running 36-38 psi on Star specs (I only buy Dunlops best bang for my Yen)

Any help most appreciated.

Link to comment
https://www.sau.com.au/forums/topic/359072-dunlop-direzza-03g-hard-or-medium/
Share on other sites

Hi Mike,

I use the 03G hard on the sprint track at Queensland raceway. I also drive on the to and from the track (about 40km) I do this around 5-6 times a year however sessions are much shorter around 6 minutes with laps under the 60second mark. The tyres last me all year.

Pressure, the 3G's like 30-32psi hot so start with whatever you need for them to come up to this. I suspect 30 minutes of racing you'll need to start them pretty soft but id only be guessing but 22 might be a good start. I have different starting pressure for each tyre to suit QR, the lowest is 23 and highest is 28. So that should give you some idea.

Start with 22 and come in after say 5 laps as they should be stabilised by then ad make sure you have a temp probe or gun and change the camber accordingly.

Hope that helps?

Hi Mike,

I use the 03G hard on the sprint track at Queensland raceway. I also drive on the to and from the track (about 40km) I do this around 5-6 times a year however sessions are much shorter around 6 minutes with laps under the 60second mark. The tyres last me all year.

Pressure, the 3G's like 30-32psi hot so start with whatever you need for them to come up to this. I suspect 30 minutes of racing you'll need to start them pretty soft but id only be guessing but 22 might be a good start. I have different starting pressure for each tyre to suit QR, the lowest is 23 and highest is 28. So that should give you some idea.

Start with 22 and come in after say 5 laps as they should be stabilised by then ad make sure you have a temp probe or gun and change the camber accordingly.

Hope that helps?

Thanks for your advice Simonster.

I did not think you would run them that low initially for fear of rolling them of the rim but they have a rigid side wall I guess.

What sort of camber do you run?

I will get an infrared gun for sure.

Thanks once again.

Thanks for your advice Simonster.

I did not think you would run them that low initially for fear of rolling them of the rim but they have a rigid side wall I guess.

The sidewalls are very stiff compared to a road tyre, so no issue. I really swerve from side to side on the out lap to generate some heat, i did the same thing each time and my pressures are always spot on at the end of a run.

I suspect suzuka would be similar as far as camber goes but if you're in a GTR you may need a bit more on the front, but the temp will tell you.Also if you can't get it to turn toe the rear out at least 1mm each side this will help it point and get to the apex if you have done everything else and she's still understeering. This way you can keep some sensible camber on the front which will help with braking.

What sort of camber do you run?

-3.5 on the front -2 on the rear. but that's what i need to run to get and even temp on the tyre face for that track. It will be different at different tracks :thumbsup:

Hope it goes well!!

Edited by Simonster

suzuka is a great track. if you are not too worried about outright times, go the hards but the mediums will definitely give faster times. also depends what time of the year you are there. it's pretty cold in winter/autumn so if you're going in the cold months you may find the hards don't get enough heat into them to be useful in which case again you'll want mediums.

for transit to and from the track I would run around 34psi. on the track somewhere between 30 and 34psi hot will be what works. need a bit of experimentation to see what works for you. depending on ambient and track temps the tyres will come up by different pressures. maybe start with 25-26psi first, do 2 flying laps them come in and check the pressures. yes temp across the tyre is important, try to get it as even as possible. the infra-red heat guns are ok, but for type temps are probe is much better.

most of all, have fun. Suzuka is one of the best tracks in the world, quite fast but also quite technical and challenging. I know quite a few guys in that area (people from Voltex suzuka). it's a nice place. Hopefully you get to do the full track layout, the short layout is ok, but not the same. :)

suzuka is a great track. if you are not too worried about outright times, go the hards but the mediums will definitely give faster times. also depends what time of the year you are there. it's pretty cold in winter/autumn so if you're going in the cold months you may find the hards don't get enough heat into them to be useful in which case again you'll want mediums.

for transit to and from the track I would run around 34psi. on the track somewhere between 30 and 34psi hot will be what works. need a bit of experimentation to see what works for you. depending on ambient and track temps the tyres will come up by different pressures. maybe start with 25-26psi first, do 2 flying laps them come in and check the pressures. yes temp across the tyre is important, try to get it as even as possible. the infra-red heat guns are ok, but for type temps are probe is much better.

most of all, have fun. Suzuka is one of the best tracks in the world, quite fast but also quite technical and challenging. I know quite a few guys in that area (people from Voltex suzuka). it's a nice place. Hopefully you get to do the full track layout, the short layout is ok, but not the same. :)

The sidewalls are very stiff compared to a road tyre, so no issue. I really swerve from side to side on the out lap to generate some heat, i did the same thing each time and my pressures are always spot on at the end of a run.

I suspect suzuka would be similar as far as camber goes but if you're in a GTR you may need a bit more on the front, but the temp will tell you.Also if you can't get it to turn toe the rear out at least 1mm each side this will help it point and get to the apex if you have done everything else and she's still understeering. This way you can keep some sensible camber on the front which will help with braking.

-3.5 on the front -2 on the rear. but that's what i need to run to get and even temp on the tyre face for that track. It will be different at different tracks :thumbsup:

Hope it goes well!!

Simonster thanks for all the great tips and advice I will put it to good use. :cheers:

suzuka is a great track. if you are not too worried about outright times, go the hards but the mediums will definitely give faster times. also depends what time of the year you are there. it's pretty cold in winter/autumn so if you're going in the cold months you may find the hards don't get enough heat into them to be useful in which case again you'll want mediums.

for transit to and from the track I would run around 34psi. on the track somewhere between 30 and 34psi hot will be what works. need a bit of experimentation to see what works for you. depending on ambient and track temps the tyres will come up by different pressures. maybe start with 25-26psi first, do 2 flying laps them come in and check the pressures. yes temp across the tyre is important, try to get it as even as possible. the infra-red heat guns are ok, but for type temps are probe is much better.

most of all, have fun. Suzuka is one of the best tracks in the world, quite fast but also quite technical and challenging. I know quite a few guys in that area (people from Voltex suzuka). it's a nice place. Hopefully you get to do the full track layout, the short layout is ok, but not the same. :)

Thanks Beer Baron, My car can go a lot faster than I can drive it at this stage. So am just out to try and improve my er lack of skills... I had thought about the mediums but did not want to wear them out driving to and from the track. Going there in June but have a few runs planned in August and September also . Probably hard is best.

Its the full 5K track and its gonna be a great day. :cheers:

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...