Jump to content
SAU Community

Recommended Posts

Morning everyone :)

I have been looking around on carsales.com.au for R33 GTR's over the last few days. I have checked all states for price differences etc etc.

Now there are only a few for sale in WA and they are $27K+.

In the Eastern States, prices range from the high teens through to the mid twenties for an R33 GTR, Series 1/2/3, low & high km, molested or not.

Now, I've never owned a GTR, however I have done a lot of reading about the mechanical components and am no stranger to the problems that can occur with the RB26 motors etc.

I'm just after some advice as to whether i would be better off spending $26-$27K in WA for a GTR that is already here and registered etc or whether i should go interstate? I've never brought a vehicle interstate so I would be extremely careful.

THIS R33 GTR is in Perth and has been for sale for the last ~14months. I looked at the car and drive it this time last year; the body work is immaculate, it drives very smoothly and the engine does not make any unusual noises. Oil pressure seems to be fine. Modifications on this 96 R33 are limited to a cat-back exhaust, intake, aftermarket coilpacks and x-drilled rotors. The guy that owns it is in his mid-late 50's; he told he purchased the GTR from a friend in SA and has never experienced any major issues with the vehicle. In the comments, the owner advises a new tailshaft center bearing assembly has been installed. Why would this have been done (from driving the car hard, general wear & tear??). Not sure why it has not sold as of yet? If I were to consider buying it, I would put the vehicle on hoist to check it out. Would it be worth getting a compression test done on the motor?

THIS R33 GTR is at a dealer in Victoria. Comments say just imported with 76,000kms. Now it's only $22K. Would it be worth taking the risk, flying over the Vic for the day, seeing the car and buying it/trucking it to WA?

Thank you in advance for any information/advice offered.

Cheers,

Jace.

Mods please move to correct section if need be.

Edited by syfon
Link to comment
https://www.sau.com.au/forums/topic/359856-r33-gtr/
Share on other sites

...

Mods please move to correct section if need be.

WA car: As this is a vspec (check the vins to confirm this) this would account for the some of the price difference. An engine compression test is a must. I would also get a paint thickness test done to check for accident history and to ensure it is an orginal midnight purple (also attracts a slight premium).

Vic car: I would be flying over to look at this or at the very least getting an idependent mechanic to look it over. Again compression test, paint thickness test and vins check are a must.

Both cars have nismo aftermarket dashes, so the advertised km's are probally dodgey. I would be looking for edvidence of the 100,000km service (e.g. timing belt) on both cars - if not, get it done asap on purchase. The wa car has been in australia a while, so recent service history is documented which is also a bonus.

It will cost ~$1000+ to transport the car over to perth, but will be pretty easy (no pits required by memory) and cheap to get the rego changed over.

IMHO i would be leaning towards the WA car, just for convinience. However, both cars look good, but i would be pricing the actually cost of buying the interstate car (e.g. transport, flight, mechanics, rego etc) before making a deceision.

Link to comment
https://www.sau.com.au/forums/topic/359856-r33-gtr/#findComment-5746452
Share on other sites

WA car: As this is a vspec (check the vins to confirm this) this would account for the some of the price difference. An engine compression test is a must. I would also get a paint thickness test done to check for accident history and to ensure it is an orginal midnight purple (also attracts a slight premium).

Vic car: I would be flying over to look at this or at the very least getting an idependent mechanic to look it over. Again compression test, paint thickness test and vins check are a must.

Both cars have nismo aftermarket dashes, so the advertised km's are probally dodgey. I would be looking for edvidence of the 100,000km service (e.g. timing belt) on both cars - if not, get it done asap on purchase. The wa car has been in australia a while, so recent service history is documented which is also a bonus.

It will cost ~$1000+ to transport the car over to perth, but will be pretty easy (no pits required by memory) and cheap to get the rego changed over.

IMHO i would be leaning towards the WA car, just for convinience. However, both cars look good, but i would be pricing the actually cost of buying the interstate car (e.g. transport, flight, mechanics, rego etc) before making a deceision.

Yes, I understand being a v-spec and midnight purple does attract a slight premium. I am aware it has an aftermarket Nismo dash, however the condition of the car does suit the KM. I mean, the car is in excellent condition and the owner seems as though he really takes good care of it. The Perth gtr has been in WA for almost 4 years (i found out through my work :P). I will get the VIN number of the perth gtr (shown in carsales pics) and ask in the VINS-Fasted thread. When i went over the car ~12months ago, I could not find any evidence what so ever of an accident.

I have a mechanic who would be more than happy to spend an hour or two going over the car with a fine tooth comb. Roughly how much does a compression test cost? If I buy the GTR in Perth, I won't be modifying it at all (other than what is already done), and it will only be a weekend car with the occasional drive to work.

Thanks for your advice, much appreciated!

Link to comment
https://www.sau.com.au/forums/topic/359856-r33-gtr/#findComment-5746496
Share on other sites

I have a mechanic who would be more than happy to spend an hour or two going over the car with a fine tooth comb. Roughly how much does a compression test cost? If I buy the GTR in Perth, I won't be modifying it at all (other than what is already done), and it will only be a weekend car with the occasional drive to work.

If your feeling handy: Analogue Compression tester at supercheap auto =~$50 bucks. There are instructions somewhere on this forum on how to do the test.

Otherwise, when your mechanic looks over the car, request a compression test - should take ~15-30mins. Should only cost the labour time.

Link to comment
https://www.sau.com.au/forums/topic/359856-r33-gtr/#findComment-5746563
Share on other sites

When Rohan advertised his LM, he was using that as a base comparison in price for sale.

Back then it had 106 or 108ish kms on it. (Can't remember if stock dash or not. PM gersfan)

When i checked it out last year it had the Nismo dash then.

Maybe he is advertising it as just the kms on the Nismo dash?

Mmmm will PM Gersfan.

Cheers James

Link to comment
https://www.sau.com.au/forums/topic/359856-r33-gtr/#findComment-5746564
Share on other sites

If your feeling handy: Analogue Compression tester at supercheap auto =~$50 bucks. There are instructions somewhere on this forum on how to do the test.

Otherwise, when your mechanic looks over the car, request a compression test - should take ~15-30mins. Should only cost the labour time.

Ok no worries. Will look into it.

My mechanic won't charge me though :P lol

Link to comment
https://www.sau.com.au/forums/topic/359856-r33-gtr/#findComment-5746566
Share on other sites

Honestly, I'm looking for something around the $20-$22K mark.

I would prefer one with just an exhaust and intake - no major mods (even the standard wheels and suspension). But I'm really after one with a flawless body and this MNP one in Perth has that.

Will keep searching around, I have plenty of time :)

Link to comment
https://www.sau.com.au/forums/topic/359856-r33-gtr/#findComment-5746577
Share on other sites

What about this one?

http://www.skylinesa...r33-gtr-v-spec/

I checked it out when I was in the market for a GTR, but decided in the end I wanted an R32. Really genuine guy. The car was pretty BONE stock when he got it IIRC. Not even catback exhaust. Here's the thread he made when he first bought it.

http://www.skylinesa...r-a-real-beast/

Might be what you're after?

Edit: Just read your post in his for sale thread hohohorolleyes.gif

Edited by PewPew
Link to comment
https://www.sau.com.au/forums/topic/359856-r33-gtr/#findComment-5749253
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...