Jump to content
SAU Community

Recommended Posts

Hey Gurus and Gurettes, my front/ rear torque gauge thing(to the left side of cluster) doesn't respond and sometimes my rear tyres screech around corners, does this mean I'm only running 2wd? I havnt pushed her too hard yet so pretty important to knOw.

-----------

Update;

Ok, silly me. all this talk about fuse breakers made me do the obvious.. CHECK MY FUSES!! Turns out my(under the hood) 4wd fuse was put in the empty spot nxt to where it should have been. It look intact so I went to put it in place(with ignition off obviously) and I could hear a buzzing from the rear of the car so I panicked and pulled it. Is this normal? Can any of u gurus work out why he would have moved the fuse out of line? Cheers all.

Jesse.

Link to comment
https://www.sau.com.au/forums/topic/360001-hey-guys-some-advice/
Share on other sites

That's what I thought, Bubba.. I'm gonna have a go flushing and bleeding the system today and I'll see what happens. The previous owner said there was a leak somewhere is the system, does anyone know of a weak spot or somewhere it's most likely to leak from?

Hi all, I'm still stuck here, any advice would be greatly appreciated. :)

I will start from the beginning and hopefully someone here has experienced this before or can suggest trouble shooting methods.

When I bought my 89 GTR(as even more of a skyline noon than I currently am!) the previous owner told me the 4wd function wasn't working properly and had been "switched off" by a nissan mechanic due "a leaking switch". He was leaving for nz for a few weeks the next morning so I bought it on the spot(impulse buy and a half). Having read countless pages on the attessa system on both this site and others I began my own basic troubleshooting.

1. Fuses: cabin 4wd fuse is intact. In-bonnet 4wd fuse intact but moved to the "spare" fuse slot! Tried the fuse in position with my keys in my hand and immediately heard a buzzing sound from roughly under the rear seats. Not knowing what this was I quickly pulled the fuse out again.

2. Fluids/reservoir: Checked my attessa fluid level(thanks BWRGTR!) which was very low. Got some TQ-DIII to fill with and ended out pulling the entire reservoir out with the hoses so I could drain it fully and clean it off. The previous owner also mentioned there might be a leak in the attessa tank itself and this looked believable by the residue on it and the hoses. After close inspection I was sure it must have just been spilt when filling. Refitted.

3. Filling and bleeding: Followed the DIY by Black R32(thanks dude!) but wanted to get some fluid through the system before getting the attessa motor going. Filled the reservoir through the top filler cap pretty much to the top. Now I wasn't sure how to bleed the fluid into the bottom half of the reservoir. First tried loosening the bleeding nipple on the nipple closest to the front of the car and had abOut 30ml of what looked like this come out..

23a89e84.jpg

Next I disconnected the air bleed connector plug with the bleeding point cracked and then tried the fuse in the engine bay again. It is important to note that when the fuse is properly inline the Attessa pump can be heard buzzing and does not stop so after a few seconds I pulled the fuse back out. This time the reservoir was half empty meaning some of the fluid had bled somewhere. I refilled reservoir and went to repeat the steps. This time though the fuse was stuck in the fuse box and the pump ran for about 15 seconds then stopped. Once I got the fuse out I saw the reservoir level had barely changed, nothing more had bled from under the car but now there was sh1tloads of(still fairly clean, red) the tranny fluid running down most sides of what I think is my rear diff..!

Diagnosis: Guys, what have I possibly broken/blown up here?

Being that the fluid running was the fluid I had just put in, it is probably attessa only related and therefore car can still be driven in RWD? If this is the case could it have already have been leaking and maybe the leak Old Mate who used to own the car was talking about?

Any which way, has anyone ever been through this or would know the best way to begin dealing with this? Important, I don't own ramps so this work was done with my rear wheels on a kerb thus my vague description of where it's leaking from.

Thankyou to ANYONE who stuck through my novel this far. :) cheers especially if anyone has light to shed on this problem I have.

Jesse.

should be, pull the fuse marked 4wd in the engine bay

did u find out what was leaking - diff??

best to take to workshop so u can look under the car properly, red fluid could the attessa fluid leaking and u might be able to fix the leak the previous owner was talking about

Well guys, got front wheels on a kern and back on ramps and I could get under it. This is what I'm pretty sure is leaking looking up diagonally toward the back of the car in just above the diff. I assume attessa. :(

2e154d17.jpg

So diff out and replace? Doesn't sound doable in my driveway.. Has anybody done it here? What's involved?

Thanks for the input guys. :)

Jesse.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...