Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
  • 2 weeks later...

Turbo's sold

love those rims, that is'nt gtr offset though, is it?

They're pretty awesome and come in at about 8kg each with out rubber. Amazingly light.

Yeah, they'll fit the GTR beautifully, haven't got any pics of them on my car but the previous owner did, I'll scrounge around and see if I can find them now.

Rb26 Head - Tomei cam studs, tomei springs, tomei phosphor guides, tomei oversized valves, and Tomei shimless buckets. Head has been decked ported and polished and has been shimmed correctly for the Jun 272 cams - $4200

Jun Oil Pump - Used - $900

Trust Oil cooler with HKS relocation kit

Set of Advan TC2 18X10.5 +25 wheels $4000

Bosch 984 fuel pump - $200

Sard FPR with lines to suit Rb26 - $250

Still for sale. Open to offers, very open

Bump

All negotiable

Found some random crap laying around.

Stock Intercooler piping for gtr

Stock r34 gtr ecu

Stock Rb26 Cam gears.

Aftermarket pressure side turbo piping (the thing that has 'Twin Turbo' written on in on a stock setup)

Bump

All negotiable

Found some random crap laying around.

Stock Intercooler piping for gtr

Stock r34 gtr ecu

Stock Rb26 Cam gears.

Aftermarket pressure side turbo piping (the thing that has 'Twin Turbo' written on in on a stock setup)

Pics of the turbo piping please.

  • 2 weeks later...

Yeah, had this installed on the car. Changed it to a stock pipe for aesthetic reasons.

$200? ONO i don't know what it is or what it's worth

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...