Jump to content
SAU Community

Recommended Posts

I just got defected today driving my uncomplied unregisted r32 gtr from the mechanics back to my house on a permit.

I had no front bar because it was at the crash repairs getting some cracks fixed, and whilst i was driving it home my front right indicator fell off unknowingly.

the officer deamed the car unroadworthy and defected me. the car will be getting complied sometime in the near future maybe 3-6 months.

will this defect have to be removed (rectified) before i go to get complied or when its getting complied or after? or is it just nothing to worry about?

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/361051-defect-on-permit/
Share on other sites

There is a dedicated defect thread in this forum for questions like these. Otherwise we'll have hundreds of defect threads from various posters.

Expect this thread to be locked and/or removed.

You'll find your answer in the defect thread.

:thumbsup:

I wouldn't worry too much - I know this isnt the exact same situation but me and a mate of mine both took our R32's through Regency around the same time for a RB25DET conversion, his was defected, mine was not. I don't believe there was any difference at all in how the cars were checked and the owners treated.

Get the defect notice signed off once you go through so you can hand it into the rego office to get rego for your car.

You might have to pay more for it though as it's meant to be a different type of inspection to your ID one to gain rego.

Easy done though.

I would have laughed at the cop, as the car is uncomplied it is, and always was not compliant with ADR's and therefore is defectable. But as the car has to be complied you are in effect clearing the defect when you get it complied, just rip the sticker off, it means nothing in this case.

I would have laughed at the cop, as the car is uncomplied it is, and always was not compliant with ADR's and therefore is defectable. But as the car has to be complied you are in effect clearing the defect when you get it complied, just rip the sticker off, it means nothing in this case.

true.... but leave the sticker. its not worth the immenant fine that you would get

I would have laughed at the cop, as the car is uncomplied it is, and always was not compliant with ADR's and therefore is defectable. But as the car has to be complied you are in effect clearing the defect when you get it complied, just rip the sticker off, it means nothing in this case.

Rip the sticker off if you never plan on regoing the car but leave it on if you do plan on getting rego.

They would have defected the vin number of the car so he would need to get it cleared off the system so he would need to get his defect paper work sorted at the same time and removing the sticker wouldn't be a good idea haha.

as the car hasn't been complied, there is no VIN in the system. The VIN the car will end up with will be an 1MPORT xxx xxxx VIN which the car hasn't got yet.

Anyhow there is no harm in leaving the sticker on but i still would have laughed at the copper.

as the car hasn't been complied, there is no VIN in the system. The VIN the car will end up with will be an 1MPORT xxx xxxx VIN which the car hasn't got yet.

Anyhow there is no harm in leaving the sticker on but i still would have laughed at the copper.

Those VIN numbers were issued with tho old Import scheme, It will be given a VIN, 6U90 - then your chassis no, more Zeros added to to take it up to 17 digits if required.

Those VIN numbers were issued with tho old Import scheme, It will be given a VIN, 6U90 - then your chassis no, more Zeros added to to take it up to 17 digits if required.

so if my vin/chassis numbers are in the system with a defect to there name, when they add onto the numbers for compliance it wont show that it has a defect on it when i go to get rego?

Thanks.

so if my vin/chassis numbers are in the system with a defect to there name, when they add onto the numbers for compliance it wont show that it has a defect on it when i go to get rego?

Thanks.

Im pretty sure when you take the car in for inspection, it wont be "on the system" yet as a car on the road. Doing the roadworthy to get rego is clearing it at the same time also, so once inspected, they would then add you and at the same time it would be cleared of any defect.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...