Jump to content
SAU Community

Need standard height

JaseR33
 Share

Recommended Posts

JaseR33 Collaborator

JaseR33

Posted
Posted

Hi,

Can someone please tell me what the standard height of an R33 GTS25T is? I've seen a whiteline article that implies that it is 370mm from centre wheel to guard but have called a few suspension shops who dispute this. I'm considering getting Bilstein shocks, but am hesitant cos my height is 330mm at the moment. Need to know the height cos shocks may stuff up quick if car's too low.

Thanks

Jason

Link to comment
https://www.sau.com.au/forums/topic/36115-need-standard-height/
Share on other sites
Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi Jason, the Nissan homologation papers say 370 mm standard, centre of wheel to guard when new. I usually subtract about 10 mm for initial settle in. I have never seen a truly standard one under 360 mm, so based on my experience 370 mm is correct.

As for lower, they handle best at 350/340 mm, any lower and the suspension geometry (camber change angles particularly) turn to crap. Plus you loose power through the accentuated drive shaft angles. Lower = slower.

Hope that helps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • GTSBoy
      R33 GTR running -9 with no tune

      By GTSBoy · Posted

      So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around without a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
×
×
  • Create New...