Jump to content
SAU Community

Recommended Posts

I have for sale the v35 18" coupe stockies, potenzas front, brand new cheap tyres on rear, was thinking 600$? you all know what they look like not sure what they are worth, contact me on 0410694161 as I'm new to the site and dont think im enabled to PM just yet, located newcastle NSW cheers

Edited by Texas G
Link to comment
https://www.sau.com.au/forums/topic/361640-fs-18-g-stockies/
Share on other sites

I have for sale the v35 18" coupe stockies, potenzas front, brand new cheap tyres on rear, was thinking 600$? you all know what they look like not sure what they are worth, contact me on 0410694161 as I'm new to the site and dont think im enabled to PM just yet, located newcastle NSW cheers

Sounds like a good deal. Posting a few pics so ppl can see the quality of the rims would be a good marketing tip thumbsup.gif

If only you were in Perth I would've given it a punt.

wouldve bought them if you were in Melb.

post up the pics ??

Coupe uses staggered rims doesn't it?

Maybe get them sent down via Greyhound. You'll have to pick them up from the Greyhound depot, but it is a cheaper way of shipping...

The coupe 18's run the same +30 front and rear but run 225 front 245 rear. The weird thing is they are marked "F" and "R". The only difference I can see is the rears look to have more bracing around the inside of the hub. Hang on this is for the 2003 type 18" coupe wheels with Brembo's.

Edited by omp

if you want closer pics of the rash i'll mms it to you, if noone buys them im going to sand them back, fill them and powdercoat them

post-84440-0-78894000-1303698845_thumb.jpg

shippin to melb could be pretty pricey

also if youre puttin them on an m35 you wont run these tyres will you, i have 235/35/18 tyres for extra if youre interested

Edited by Texas G

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...