Jump to content
SAU Community

Recommended Posts

Hey guys,

im guessing im having a problem with my steering wheel i have no horn, also the airbag light is on

have checked all fuses n connections to the horn so im leaning towards the wheel itself, also have noticed the hicas light comes on when on the freeway.

could it be a loose connection or something? but hesitant a pulling the wheel off incase the airbag goes off.

anyone else have this problem? or no of a fix?

thanks heaps

btw its a r33 GTR

Edited by jetblack
Link to comment
https://www.sau.com.au/forums/topic/361788-steering-wheel-problems/
Share on other sites

Not too sure about your horn, but to turn off or reset your airbag light, you need to go through this process:

Open drivers side door, but press and hold the little door sensor (so the car think the door is closed), then turn key to ignition without starting the car, then quickly press that door sensor at least 7 times and just hold it. Then just turn car off.

But it does sound like theres something wrong with your steering wheel.

Clock-spring

/thread

If you've taken a steering wheel off before, you'll notice there's a brass bush sprung against a round wheel, that transmits power (or usually earth) to the horn button, so that the wheel can rotate lock to lock without breaking wires etc.

Problem being that this might be OK for a horn button, but for something like an airbag that needs a guaranteed connection %100 of the time in the event of an accident, not so good. So they use a clock-spring (google it), a continuous piece of wire that can operate with the wheel turning, and incorporate the horn button wiring (usually) into it as well.

But now that the cars 10+ years old, 100,000+km, and has gone through 1000's of turns, they wear out.

Best bet, get it checked by a workshop with a compatible scan tool, and they should be able to determine the fault.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...