Jump to content
SAU Community

Nytsky Spec Built Rb25

Supa Steve
 Share

Recommended Posts

Supa Steve Enthusiast

Supa Steve

Posted
Posted

Fresh RB25 for sale built to same spec as NYTSKY's 430rwkw engine by Red R Racing

Acid dipped, crack tested, bored and strainer plate honed block

crack tested, cross drilled and grub screwed crankshaft

resized, honed and cryo treated RB26 conrods with ARP bolts fitted

CP 86.5mm forged piston kit with custom Red R ring package

ACL race series engine bearings

Nissan N1 oil pump and water pump

Gates timing belt kit with pulleys

cometic 1.2mm head gasket

fully reco'd cylinder head

HKS 256/264 camshafts

OS giken exhaust cam gear

HKS 850cc injectors

Twin scroll stainless manifold

50mm external gate

plazmaman inlet manifold

80mm throttle body

engine is only missing a turbo as im using the t04z twin scroll on my 30/26 engine.

it comes with an option of a Red R 8.5 litre sump fitted

this combo is a proven performer built by one of the best RB builders in aust.

$8900 or $9500 with race sump

Link to comment
https://www.sau.com.au/forums/topic/362039-nytsky-spec-built-rb25/
Share on other sites
Supa Steve Enthusiast

Supa Steve

Posted
  • Author
Posted

Supa Steve,

Can you ask your mate, Paul, to either call me and/or send me my oil pump please. He seems to be uncontactable.

you may need to leave a message if you cant get hold of him NX. Ive got to call them tommorrow to arrange an inspection of the engine for a buyer so ill let Paul know.

PM's replied to.

Supa Steve Enthusiast

Supa Steve

Posted
  • Author
Posted

to those pm'ing about warranty, Paul stands by his work and is prepared to provide start-up warranty as well as advice on run-in procedure etc.

his after sales service is excellent and looks after customers long after engine is installed running and tuned.

NXTIME Grand Master

NXTIME

Posted
Posted

you may need to leave a message if you cant get hold of him NX. Ive got to call them tommorrow to arrange an inspection of the engine for a buyer so ill let Paul know.

PM's replied to.

Mate,

Paul is well aware of the situation (and I have spoken/sms'd/left messages to him many, many times about it) and I am sure he knows what must be done. Perhaps you could quietly remind him again when you see/speak to him next.

Thank you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...