Jump to content
SAU Community

Recommended Posts

DSC_9788.jpg

HKS SLD Type I (Speed Limit Defencer). This is a handy device to remove your factory speed cut the proper way. This is a universal unit compatible a LOT of vehicles. I'll just list out the Nissan ones here:-

Nissan Fairlady Z CZ32 Eng: VG30DETT

Nissan Fairlady Z PZ31 Eng: RB20DET

Nissan Skyline DR30 Eng: FJ20E

Nissan Skyline DR30 Eng: FJ20ET

Nissan Skyline HR31 Eng: RB20DET

Nissan Skyline GTS-4 HNR32 Eng: RB20DET

Nissan Skyline GTS HCR32 Eng: RB20DET

Nissan Skyline GT-R BNR32 Eng: RB26DETT

Nissan Skyline GTS25 ECR33 Eng: RB25DET

Nissan Skyline GT-R BCNR33 Eng: RB26DETT

Nissan Skyline GT HR34 Eng: RB20DE

Nissan Skyline 25GT ER34 Eng: RB25DE

Nissan Skyline 25GT Turbo ER34 Eng: RB25DET

Nissan Skyline GT-R BNR34 Eng: RB26DETT

Nissan Stagea PM35 Eng: VQ35DE

Nissan Stagea M35 Eng: VQ25DD

Nissan Stagea 25RS V WGC34 Eng: RB25DET

Nissan Stagea 260RS WGNC34 RB26DETT

Nissan Leopard J. Ferry JGBY32 Eng: VH41DE

Nissan Silvia S13 Eng: CA18DE

Nissan Silvia S13 Eng: CA18DET

Nissan Silvia PS13 Eng: SR20DE

Nissan Silvia PS13 Eng: SR20DET

Nissan 180SX RS13 Eng: CA18DET

Nissan 180SX RPS13 Eng: SR20DET

Nissan Silvia S14 Eng: SR20DE

Nissan Silvia S14 SR20DET

Nissan Silvia S15 Eng: SR20DE

Nissan Silvia S15 Eng: SR20DET

Nissan Cefiro PA32 Eng: VQ25DE

Nissan Cefiro A31 Eng: RB20DET

Nissan Cefiro LA31 Eng: RB20DET

Nissan Pulsar GTI-R RNN14 Eng: SR20DET

Nissan Pulsar GT-i HN15 Eng: SR18DE

Nissan Pulsar EN13 Eng: CA16DE

Nissan Cube Z10 Eng: CG13DE

Link to comment
https://www.sau.com.au/forums/topic/364397-hks-sld-type-i/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...