Jump to content
SAU Community

Recommended Posts

Haltech Platinum Pro Plug-in ECU - Nissan Skyline 32GTST/ 32 GTR for sale

Brand NEW never used ever in box ready to go

Car stolen so i have no use for this now

$1500.00 inc postage

..............................................................................

Features:

• Direct plug and play replacement of the OEM ECU, no rewiring necessary.

• Uses the cars factory sensors

• Supports R32 GT-R twin MAF sensors

• Supports Sequential Injection (peak and hold) and Direct fire ignition

• Windows 2000, XP, Vista compatible software

• Real time programming, instant hesitation free adjustment while engine is running

• Fully user definable 32 x 32 mapping

• Tuning via Volumetric Efficiency (VE), Injection time or Lambda Correction (MAF)

• Selectable onboard internal MAP sensor rated to 150kPa (up to 1.5 Bar or 22psi boost)

• Wideband “auto tuning” using user definable target AFR table

• USB and CAN Communication Port

Factory Outputs:

• 6 x Fuel Injector outputs

• 6 x Ignition outputs

• Tacho, Boost Control, AC Clutch Relay, Idle Control

• Thermo Fan, Check Engine Light, Fuel Pump (Variable Speed)

• N-VCT ( Nissan Variable CAM Timing Control)

Factory Inputs:

• MAF sensors, Throttle Position Sensor, Oxygen sensors,

• Coolant Temperature sensor, Vehicle Speed Sensor,

• Air Temperature sensor.

Expansion I/O*:

• 2 x Analogue Voltage inputs

• 2 x Analogue Temperature inputs

• 4 x Digital pulsed outputs

*Optional auxiliary harness required to be purchased Haltech Part # HT040003

Functions:

• Closed Loop O2 Control

• Decel Cut Over Boost Rev Limiter

• Closed & Open Loop Boost Control

• Gear Setup

• ACF On Base Tables

• Transient Throttle Enhance

Correction Tables: Fuel Ignition Boost:

• Cranking

• Air Temp Target Correction

• Coolant Temperature Correction

• Map Correction

• Zero Throttle Gear Correction

• Cylinder Trim

• TPS Correction

• Generic Correction 1

• Generic Correction 2

• Gear Correction

• Post Start

• Air Temp Duty Correction

• Post Start

Miscellaneous:

• Data Logging: 448Kb of onboard data logging, Storage for approx 40 minutes at 10 logs per seconds, 6 channels of data

• Max 20 channels logging capability

• Tune can be password protected in software

• Rugged anodized aluminum casing

Power Requirements:

Source: 8.6 to 16.5 Volts DC

Consumption: 530mA @ 12Volts DC

Physical Dimensions:

Length: 154mm (174mm with MAP nipple)

Width: 158mm Height: 42mm Weight: 680g (1.5 lb)

Vehicle Compatibility:

• Nissan Skyline R32 GTR (RB26DETT)

• Nissan Skyline R33 GTR (RB26DETT)

• Nissan Skyline R33 GTS-T (RB25DET)

Transmission Compatibility:

• Manual only (Automatic not supported)

Platinum Pro Plug-in Kit Contents:

• Pro Plug-in ECU

• USB Cable

• Programming Software CD

• Quick Start Guide

• Instruction Manual (CD)

  • 2 weeks later...

hey would you take $1200 for it??

Haltech Platinum Pro Plug-in ECU - Nissan Skyline 32GTST/ 32 GTR for sale

Brand NEW never used ever in box ready to go

Car stolen so i have no use for this now

$1500.00 inc postage

..............................................................................

Features:

• Direct plug and play replacement of the OEM ECU, no rewiring necessary.

• Uses the cars factory sensors

• Supports R32 GT-R twin MAF sensors

• Supports Sequential Injection (peak and hold) and Direct fire ignition

• Windows 2000, XP, Vista compatible software

• Real time programming, instant hesitation free adjustment while engine is running

• Fully user definable 32 x 32 mapping

• Tuning via Volumetric Efficiency (VE), Injection time or Lambda Correction (MAF)

• Selectable onboard internal MAP sensor rated to 150kPa (up to 1.5 Bar or 22psi boost)

• Wideband "auto tuning" using user definable target AFR table

• USB and CAN Communication Port

Factory Outputs:

• 6 x Fuel Injector outputs

• 6 x Ignition outputs

• Tacho, Boost Control, AC Clutch Relay, Idle Control

• Thermo Fan, Check Engine Light, Fuel Pump (Variable Speed)

• N-VCT ( Nissan Variable CAM Timing Control)

Factory Inputs:

• MAF sensors, Throttle Position Sensor, Oxygen sensors,

• Coolant Temperature sensor, Vehicle Speed Sensor,

• Air Temperature sensor.

Expansion I/O*:

• 2 x Analogue Voltage inputs

• 2 x Analogue Temperature inputs

• 4 x Digital pulsed outputs

*Optional auxiliary harness required to be purchased Haltech Part # HT040003

Functions:

• Closed Loop O2 Control

• Decel Cut Over Boost Rev Limiter

• Closed & Open Loop Boost Control

• Gear Setup

• ACF On Base Tables

• Transient Throttle Enhance

Correction Tables: Fuel Ignition Boost:

• Cranking

• Air Temp Target Correction

• Coolant Temperature Correction

• Map Correction

• Zero Throttle Gear Correction

• Cylinder Trim

• TPS Correction

• Generic Correction 1

• Generic Correction 2

• Gear Correction

• Post Start

• Air Temp Duty Correction

• Post Start

Miscellaneous:

• Data Logging: 448Kb of onboard data logging, Storage for approx 40 minutes at 10 logs per seconds, 6 channels of data

• Max 20 channels logging capability

• Tune can be password protected in software

• Rugged anodized aluminum casing

Power Requirements:

Source: 8.6 to 16.5 Volts DC

Consumption: 530mA @ 12Volts DC

Physical Dimensions:

Length: 154mm (174mm with MAP nipple)

Width: 158mm Height: 42mm Weight: 680g (1.5 lb)

Vehicle Compatibility:

• Nissan Skyline R32 GTR (RB26DETT)

• Nissan Skyline R33 GTR (RB26DETT)

• Nissan Skyline R33 GTS-T (RB25DET)

Transmission Compatibility:

• Manual only (Automatic not supported)

Platinum Pro Plug-in Kit Contents:

• Pro Plug-in ECU

• USB Cable

• Programming Software CD

• Quick Start Guide

• Instruction Manual (CD)

got this from eBay through the seller, paid by the paypal the first minute after the sale, he refused to send the item because paypal needs the trucking number in order to release the fund into his account, i did try to convince the seller to finalize the sale but ended up with no luck, therefore have to wait a month time to go through the dispute to get the money back.......

just a friendly reminder to the potential buyers, cheers.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...