Jump to content
SAU Community

Rb24,r32,r33,everything! Ono!

kngtut
 Share

Recommended Posts

kngtut Contributor

kngtut

Posted
Posted

HI. HERE I HAVE A LIST OF THINGS FROM A STRIPPED RB24 THAT I MUST GET RID OF TO PAY FOR FOR SOME MEDICAL BILLS IN A HURRY.

1. A SET OF 6 TOMEI PISTONS WITH RB25/26 EAGLE RODS. WAS STRIPPED FROM MY BUILT RB24. ONE OF THE PISTONS MAY HAVE GONE SOFT BUT WAS TOLD CAN STILL BE USED ON LOW BOOST. EAGLE RODS ARE IMMACULATE. HAS DONE LESS THEN 5000KM. PRICE $800 NEED TO GO!!

picture013qpz.jpg

2. STRIPPED RB24. RB20 BOTTOM END WITH R32 GTR CRANK, N1 OIL PUMP, GREEDY FILTER. OIL GALLERIES HAVE BEEN MODDIFIED TO GTR SPEC. HAS BEEN LOOKED OVER AND IN EXCELLENT CONDITION. DONE LESS THEN 5000KM. PRICE $1100!!!!! ONO!!! NEEDS TO GO!!!

picture008r.jpg

3. 20 INCH DOLCE MAGS WITH 80% HANCOOK TYRES. IN EXCELLENT CONDITION. WILL FOR R32/33/34.

PRICE $1000 ONO!!!!

picture004sup.jpg

4. CUSTOM R32 PLENUM WITH SS THROTTLE BODY. MADE FOR BIG POWER. PLENUM HAS BEEN POWDER COATED. MADE BY VIC AT EAS. DONE LESS THEN 1500KM. PRICE $800 NEED IT GONE!!

picture017ld.jpg picture002dt.jpg

4. BRAND NEW ISOTTA STEERING WHEEL. STILL HAVE INVOICE FOR IT BOUGHT $200 SELL $140.

picture015e.jpg

Uploaded with ImageShack.us

5. MOMO STEERING WHEEL. EXCELLENT CONDITION. NOT SURE IF ORIGINAL OR NOT. PRICE $80!!!

picture016ow.jpg

Uploaded with ImageShack.us

MY R32 WILL ALSO BE UP FOR SALE SOON SO IF THERES ANY INTEREST PLEASE LET ME KNOW. INTERIOR DONE, 300KW, PAINTJOB, EVERYTHING DONE!!! THIS CAR IS MY PRIDE AND JOY, HAS BEEN IN HOT4'S.

picture019br.jpg

Uploaded with ImageShack.us

ALL THIS STUFF NEEDS TO GO!!!!

I AM LOCATED IN THE SOUTH EASTERN SUBURBS OF MELBOURNE. PLEASE CONTACT ME ON 0412 595 898. OR LEAVE AN SMS. THANKS EVERYONE.

Link to comment
https://www.sau.com.au/forums/topic/366180-rb24r32r33everything-ono/
Share on other sites
  • 3 weeks later...
kngtut Contributor

kngtut

Posted
  • Author
Posted

Everything reduced they need to go! 

Pistons and rods was $800 now $700!!!!

Rb20 bottom end with Gtr crank was $1100 now $950!!!!

20inch dolce mags was $1000 now $900!!!!

Custom r32 plenum and throttle body was $800 now $700!!!!!

Isotta steering wheel as NEW asking $140 will throw in delivery to any where in Australia!!!

My stuff has to go! Thanks

  • 3 months later...
kngtut Contributor

kngtut

Posted
  • Author
Posted

Yes the pistons are tomei and r pretty dure they r the 4agze. Block was bored out. But as seen in the picture is what u get. As is. So u will need ur rb20 block and bore it out. It was running a wolf 3d. Car made 320 kw safe and was a machine.....!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...