Jump to content
SAU Community

Recommended Posts

Hi Guys,

I was wondering if anyone here would be kind enough to translate this USS auction sheet (if possible, I know this might be a long long shot). I did basic Japanese back in school - but that's a distant and ancient memory now.

I have done some reading around on the internet and know how to identify the basic stuff on the auction sheet. I know there is a issue with odometer readings (*), which is basically my main concern. I know the stock odo shell was replace with a Nismo one at some point, but when (not sure if that can be gathered from this auction sheet)?

I know there are some HKS mods in there as well (but not sure what they are exactly).

Thoughts and opinions welcome.

post-85735-0-80800600-1307765463_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/367410-translating-a-uss-auction-sheet/
Share on other sites

Fair question.

As per what I have been advised, the original cluster was replace by the Nismo one at 58,000 kms in 2009. But the Nismo cluster now reads 59,000 Kms, which is why apparently the * is listed there. But again, this is all what has been advised. Not sure if this means the car is 58,000 kms + 59,000 kms = 120,000 kms (can anyone drive 59,000 kms in two years) or whether it was changed to a similar valued Nismo cluster in 2009 (I have been advised that this is what has occurred). My mechanic has given the thumbs up, but obviously I want to know roughly how many Kms the car has done whether its 59,000, 75,000 or 120,000.

Hope that makes sense.

Hey man

Well to give a short answer - there's not really any way to tell the true km of the vehicle... At least not from the auction sheet!

But here's a few clues to help you... Auction sheets list the km reading, If the km are non genuine - they used to place a ? Next to the odo reading... This is now a * because to the Japanese auction houses - and asterisk is less offensive than a question mark...

Same as why they now have a solid star instead of "grade R" for when a vehicle has been crash repaired...

So basically - nobody knows without contacting the previous owner...

BUT youll see the writing in the blurb "H19.6" which is relevant to the Nissan service year count....

So basically from what I can read (and unless anybody can prove me wrong) then your nismo dash isn't too far off the mark... Give or take maybe a few thousand km...

But honestly if you're asking because you're wondering how much you need to service it or to what extent? Given the amount of stuff written on the auction sheet id say that your service history docs should still be in your dashboard or at least stamped somewhere on a placard?

But my advise is if you're paranoid about whether or not to change waterpump..... Just do it all :) better be safe and knock it all out in the one round of labour than be sorry!!

Thank you for your advice.

As per what I have been advised, unfortunately there was no service logs that came with the car. The auction sheet was the only document provided.

The reason for the sense of paranoia is exactly because of wanting to know when to go about changing various parts.

Got a bigger image?

I can see you have a 320km Nismo meter, oil cooler, 3 HKS gauges, HKS air filter, some aftermarket muffler, roll bar etc.

You also have some worn seats & handles, slight rust under the body and a few dints patched up. Do I also see that it comes with a new car warranty card and manual?

The two rows on the top right of the line above H19.6 says that the meter is listed as altered as there are no records indicating when the Nismo meter was installed. So my guess is that they adjusted the Nismo meter to "around" 59k as you mentioned above. That said, the June 2007 inspection papers seem to say that there were 54649km on it, and 58558km in June 2009. Can't read the stuff on the right of those figures though. Something about installation or records.

Some other points:

Minor dint on the driver's side mirror?

Something done to the glovebox? Something installed inside?

Other parts still a bit hard to read. You also have a HKS intercooler and Xenon headlights though. :cool:

Edited by CT9W

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...