Jump to content
SAU Community

Recommended Posts

Hi guys and gals.

Here's the back story, Had my skyline yellowed and didn't have the time to get it off till recently (been bout a year).

The whole time the car was off the road i started it every other week to let it tick over (plus i love the sound)

Finally got it squared away and it passed the pits first time yay.

But just recently cylinder 5 has been cutting out WTF?

I narrowed it down to cylinder 5 by pulling out the plugs for each coilpack until the missing sound didn't change. I originally thought coilpack so

I changed pack 4 and 5 around but cylinder 5 still dropped out but 4 was fine. so i changed around the plugs same again. Sprayed all plugs, coils

and connections with contact cleaner still nothing.This is really giving me the shits as it happens on and off so im thinking either ECU or harness.

If anyone has had this happen to them, has an ideaor has a coilpack harness I can borrow to strike that from the list I'd love to hear from you.

Cheers people

Gavin

Link to comment
https://www.sau.com.au/forums/topic/367444-help/
Share on other sites

series1 or 1.5/2???

if series 1 try getting a hold of ignitor pack to try as well cause my 32r was dropping cylinders 6 & 4

and did the same thing changed plugs coil packs even did other things then chucked on a different ignitor a pow all fixed

Link to comment
https://www.sau.com.au/forums/topic/367444-help/#findComment-5861774
Share on other sites

At this point in time I think i need all of you to form a line and kick my ass :spank: .

I finally got round to checking the ecu with the help of a mate and it turns out the harness plug wasn't

all thje way in on all sides even though it was bolted in. It must have been done when the inspector at the pits had the kick panel off

having a look to make sure the ecu was standard I'm guessing, as i didn't have this problem

till I got backfrom the pits. So far the car hasn't missed a beat so fingers crossed that was the problem

and not something else.

Thanks to everyone for your help Ifeel like such a dumbass :blush: .

Cheers

Edited by Gabbo2047
Link to comment
https://www.sau.com.au/forums/topic/367444-help/#findComment-5862347
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...