Jump to content
SAU Community

S1 Manual G/box Conversion. Need Help! Q & A

SOB

By SOB,
in Four Door Family & Wagoneers

 Share

Recommended Posts

SOB Enthusiast

SOB

Posted
Posted

And yes I have done searches on previous threads & from that I have Questions I hope you guys can help me with or put me in touch with people who have done this. Ok my car 1998 S1. Doner car is a 2000 model RS4 S2 correct me if Iam wrong R33GTR box? Push or pull?

This is a list of parts I think I need as sourced through searches.

1. Do i need the flywheel & bolts off doner manual car or will the auto one ok? (knowledge on flywheels/transmitions limited as you can see)

2. Clutch pressure plate & bolts.

3. Spigot bush

4. Bellhousing bolts. (I think there longer in the manual)

5. Clutch master & Slave.

6. Clutch piping line

7. Clutch & Brake pedals with mounting bracket & bolts

8. Handbrake lever, mounting bracket, cable & bolts

9. CTR console

Please add to my shopping list if I have missed anything. Any help will be appreciated.

If I go ahead with project any volunteers to assist will be rewarded handsomely (Free Beer-Food)Ha! Ha!I'm in the Newcastle area. NSW

Thanks again Shane

180fan Rising Star

180fan

Posted
Posted

Is your donor car a factory manual (RS4-S) or is it an auto that was converted? If it's an RS4-S the gearbox will be pull type.

You should be able to use the flywheel from the donor car without any problems.

I dont know whether the flywheel bolts differ from auto or manual, but I would be going brand new ones from nissan anyway, rather than reusing old ones.

As for your other parts, looks like you have most of it covered. You will also need the manual footrest, and the rubber boots around the gear shifter.

I'm going to be doing the conversion very soon, here is my parts list if you want to look at it

Manualconversionpartslist.pdf

RS4-S Proficient

RS4-S

Posted
Posted

you dont have a flywheel in your stagea at the moment you have a drive plate/flex plate with a torque convertor bolted to it. you will need the flywheel as stated above. i would also say you need the flywheel bolts to suit given that the flywheel will be much thicker than the plate that comes off. not sure but possibly the gearbox mount and tailshaft are different?

SOB Enthusiast

SOB

Posted
  • Author
Posted

Thanks Taylor... When it comes to gearboxes i'm like a fish out of water. Hopefully after this conversion my knowledge on them will improve...I think i'm ok with using the auto Tailshafts & mounts as I found in a search done previous

180fan Rising Star

180fan

Posted
Posted

Cheers Brian,yes it is a factory manual. So is the factory a R33 or R32? If you don't mind me asking how much was your new clutch, spigot bush & gasket set?

I dont know whether the RS4-S is an R33 GTR or a GTS-4 gearbox, or if there is even a difference between the two. It's definitely not an R32 item though.

I cant remember the exact price off the top of my head at the moment, I bought the seal kit and clutch from www,kudosmotorsports.com, as well as a couple of other bits and pieces.

Remember that push type clutches are cheaper than pull type though, so you will probably have to pay a little bit more for whatever clutch you choose

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I neglected to respond to this previously. Get it up to 100 psi, and then you'll be OK.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      I agree with everything else, except (and I'm rethinking this as it wasn't setup how my brain first though) if the sensor is at the end of a hose which is how it has been recommended to isolate it from vibrations, then if that line had a small hole in, I could foresee potentially (not a fluid dynamic specialist) the ability for it to see a lower pressure at the sensor. But thinking through, said sensor was in the actual block, HOWEVER it was also the sensor itself that broke, so oil pressure may not have been fully reaching the sensor still. So I'm still in my same theory.   However, I 100% would be saying COOL THE OIL DOWN if it's at 125c. That would be an epic concern of mine.   Im now thinking as you did Brad that the knock detection is likely due to the bearings giving a bit more noise as pressure dropped away. Kinkstah, drop your oil, and get a sample of it (as you're draining it) and send it off for analysis.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I myself AM TOTALLY UNPREPARED TO BELIEVE that the load is higher on the track than on the dyno. If it is not happening on the dyno, I cannot see it happening on the track. The difference you are seeing is because it is hot on the track, and I am pretty sure your tuner is not belting the crap out of it on teh dyno when it starts to get hot. The only way that being hot on the track can lead to real ping, that I can think of, is if you are getting more oil (from mist in the inlet tract, or going up past the oil control rings) reducing the effective octane rating of the fuel and causing ping that way. Yeah, nah. Look at this graph which I will helpfully show you zoomed back in. As an engineer, I look at the difference in viscocity at (in your case, 125°C) and say "they're all the same number". Even though those lines are not completely collapsed down onto each other, the oil grades you are talking about (40, 50 and 60) are teh top three lines (150, 220 and 320) and as far as I am concerned, there is not enough difference between them at that temperature to be meaningful. The viscosity of 60 at 125°C is teh same as 40 at 100°C. You should not operate it under high load at high temperature. That is purely because the only way they can achieve their emissions numbers is with thin-arse oil in it, so they have to tell you to put thin oil in it for the street. They know that no-one can drive the car & engine hard enough on the street to reach the operating regime that demands the actual correct oil that the engine needs on the track. And so they tell you to put that oil in for the track. Find a way to get more air into it, or, more likely, out of it. Or add a water spray for when it's hot. Or something.   As to the leak --- a small leak that cannot cause near catastrophic volume loss in a few seconds cannot cause a low pressure condition in the engine. If the leak is large enough to drop oil pressure, then you will only get one or two shots at it before the sump is drained.
    • GTSBoy
      Help! Leak coming under transmission

      By GTSBoy · Posted

      So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
×
×
  • Create New...