Jump to content
SAU Community

Recommended Posts

1990 Nissan 180SX - Freshly Resprayed in Black with Blue Pearl

6 Cylinder RB20DET Conversion With RB 5 Speed Gearbox

Modified Exhaust Manifold to suit GT25 Series Turbo

GT2530 Ball Bearing Turbo Rated At 325HP

16”x 12” x 3” Greddy Cored Front Mounted Intercooler

Full 3” Turbo Back Exhaust System

Modified Plenum Chamber for Front mounted Throttle Body

Hi Torque “Direct Clutch” Clutch

Skyline Rear Limited Slip Diff

Bosch Rising Rate Fuel Pressure Regulator

Bosch 450HP External Fuel Pump

444cc GTR Injectors

GTR 4 Piston Calipers and Rotors

Z32 Air Flow Meter/Pod Filter

Turbosmart Type II Gated Boost Controller

Turbosmart Type III Plumed Back Blow Off Valve

Greddy Turbo Timer

Viper Alarm System with central locking

Full Whiteline Sports Package - (Adjustable Koni Shocks, Heavy Duty Sway Bars, Lowered Springs, Poly Urethane Bushes)

Avanti Amarn 17” Chrome Mags

BOMEX Body Kit

Pioneer Head Unit - (3-way Fronts with Ribbon Tweeters, 2x 10” Boxed Alpine Subs, 5 Channel Alpine Amp)

Boot Mounted Battery Conversion

Timing Belt, Water Pump, Radiator, Master Brake Cyl. all New

Car will happily support 450HP with a Simple Turbo Upgrade

REGO: NVS-180

Will post some pictures soon

$17,000 ono

Cheers,

Daniel Borrowman

[email protected]

0407289976

Link to comment
https://www.sau.com.au/forums/topic/36895-330hp-180sx/
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...