Jump to content
SAU Community

Recommended Posts

Hi guys,

I have been interested in photography for sometime and always wanted a nice camera so I finally got around to getting a Nikon D300 and now need to purchase the all important lens.

The reason I am looking at a Nikon AF-S 24-70mm f/2.8 is because it is so versatile and would pretty much cover all the photo's I could hope to take (for now anyway... I will probably get a 50mm f/1.4 down the track). What I was hoping for was some feedback from people who have used the 24-70. I know that its a full frame lens and that my camera is not but I am not too bothered because my main attraction is that it can hold f/2.8 across the entire range!

Also I know that the lens is big and heavy (the photo below says all) but that is not of concern to me, only its performance. Cheers

This is the review that I read: http://www.kenrockwell.com/nikon/24-70mm.htm

d3-24-70mm.jpg

Link to comment
https://www.sau.com.au/forums/topic/369490-nikon-af-s-24-70mm-f28/
Share on other sites

I've used it on my mates camera when he hired it. Great lens. He is actually in the states and is buying one over there as we speak.

I own a Canon 24-70 and it's basically the same. The Canon one might be a touch heavier.

If your planning on shooting wide stuff, this is not the lens for you if you don't own a FF camera. If you did own a FF camera this would be equivalent to shooting around 16mm on a crop.

A lot of lenses out there have a constant aperture of 2.8.

There is a tamron 17-50 2.8 - Have you considered that? I believe this lens is super expensive in the Nikon lineup ~$2400?

Either way, you will love how sharp it is, great walk around lens as long as you don't want to shoot wide.

I've used it on my mates camera when he hired it. Great lens. He is actually in the states and is buying one over there as we speak.

I own a Canon 24-70 and it's basically the same. The Canon one might be a touch heavier.

If your planning on shooting wide stuff, this is not the lens for you if you don't own a FF camera. If you did own a FF camera this would be equivalent to shooting around 16mm on a crop.

A lot of lenses out there have a constant aperture of 2.8.

There is a tamron 17-50 2.8 - Have you considered that? I believe this lens is super expensive in the Nikon lineup ~$2400?

Either way, you will love how sharp it is, great walk around lens as long as you don't want to shoot wide.

Hey mate,

Thanks for the reply.

I know that there are other zoom lenses that have a constant aperture of 2.8 but none of them seem to be quite as highly rated. I know that the Nikon 24-70 is expensive but I would rather spend a bit and get as good a lens as I can. I have seen them on ebay for around $1,700 - $1,800. I'll see how I go though

the equivalent crop lens is the 17-55mm 2.8 nikon which is good, but for crop sensors.

They are both good lenses, I have used both but the 24-70 is an expensive piece of glass. If you are planning to move to FF then get it, all you need is that and the 70-200VR to cover most of the photos you'll ever take. If you need wide, you can get a 17-35mm 2.8 but that's pricey too.

If money is tight you could consider the sigma 24-70 2.8 which is also a FF lens and I have that one. Bit softer when at wide apertures but at less than half the price you can't complain.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How would you even adjust the clutch if the pedal already has the correct free play? The operating cylinder has no adjustment in mounting position or rod length. On pull style clutches there is also no ability to adjust the bearing carrier. Push type I can see how adjusting the carrier height makes it all work.   If this is the twin plate clutch did you verify that your friction disks were oriented correctly? It's not mentioned in the directions at all you just have to notice that one side the friction disks have a part number on the hub fingers and a subtle coning to those fingers. Another thing that I noticed was if you put the friction disks in backwards the pressure plate fingers will not be even and flat when the clutch is installed.
    • yeah, mechanically, it is probably do-able, off the top of my head, there would be the transfer case, which I believe will bolt up to the rear of the RWD transmission, the shorter rear tail shaft. A front drive shaft, front diff, engine upper sump, front drive shafts, front hubs and front AWD struts (they are shaped around the front drive shafts), LCAs (at the very least from the front suspension) oil cooler.  You might want the rear diff from an AWD too, so you can be certain the front and rear diff rations are identical.  Who knows what brackets and mounts you might need.  So a whole doner car might be the best option if you need to maintain RHD. Then actually making it work, that would be a whole different story.
    • Take the fall as a warning sign for future endeavours  Stay safe mate
    • hi mate, HKS cooler piping still available by any chance?
×
×
  • Create New...