Jump to content
SAU Community

Recommended Posts

A couple of guys have the idea... raw fuel is injected into the hot exhaust and explodes keeping the turbo spooled up for extended periods of trailing throttle (which in the environment it is designed for amounts to durations measured in 10ths of seconds before WOT).

If you are changing gears better than most grannys you wont get jack from A/L

If it is so important buy an auto.

As fro launch, just another driver aid. Is it going to be you that sets this target time with all the electronic trickery, or are you going to attribute the time to the software boffins @ ECU HQ.

Microtech ECUs can do anti-lag and launch control. Since they have 4 different maps to choose from, Tim Possingham, a tuner here in Adelaide(based at RPM Perf Centre) has a setup that when clutch is depressed, a certain map comes on via switching on clutch that is linked to ext inputs on Microtech ECU and with I think 75% throttle at lights.

This map has heaps of fuel and very retarded timing allowing heaps of unburned fuel into exhaust and therefore pre-spooling turbo.

Then when you dump clutch it goes into normal power tune.

Then change gears, by depressing clutch and goes into anti-lag mode, etc etc

Works well I believe, used in that 300rwkW CA18 180SX that was in Zoom (was running 250rwkW at the time).

Has anyone been using launch control and anti lag for racing.

i would love to know if anti lag is any good for 1/4 mile racing as i need something to keep my boost up between gears.

any recomedations or where to get it would be excellnt.

Hi wreckedhead, you want anti lag because the engine drops off boost on gearchanges. Antilag is a bandaid, it covers the real problem, I always prefer to fix the "real problem".

As TT said, if you are changing gear too slow then learn how to change faster. If the gearbox or clutch operation is preventing you from changing gear faster, then fix the clutch and/or gearbox.

My 20 cents follows .....

If you are changing gear very fast and it still drops off boost on upchanges then you either have a tuning problem, the cooling system has too much air in it or the turbo is too big. So fix the tuning, reduce the intercooler and pipework volume or get a turbo the right size.

I would not want to stick a band aid on the problem for the track, but still have to live with it every day. I'd much rather have it fixed all the time.

PS; If it's a band aid why do WRC's run antilag? They have enough budget to fix the real problem, don't they? Yes they do, but the regulations stop them from doing it. It's one of the side effects of the small restrictors they have to run. Plus they make thousands of gearchanges during a rally and every millisecond on each gearchange counts. For 3 gearchanges per run over 1/4, I would much rather spend my money (buying and maintenance costs) on something that gives a full time result.

Sorry, that was more like 30 cents worth.

you make a good point sk

something you havent covered tho, an a/l setup should you postive pressure at idle... this must help with launching a manual vehicle assuming sufficient traction?

Yep, that's very possible. Maybe I am simply scared off antilag by the amount of damage it does to the engine, particularly exhaust valves and turbines. We used to have to fit new exhaust valves, turbines and covers after every rally on the Celica. It's a bit better now with more sophisicated ant lag software, but the maintenance still frightens me.

I will be with Neil Bates' engine builder next week, I might ask what the Corrolla's look like in that area after each rally.

you make a good point sk

something you havent covered tho, an a/l setup should you postive pressure at idle... this must help with launching a manual vehicle assuming sufficient traction?

As said in an earlier post in this thread, the two cars I've see with launch control would generate boost when stationary and waiting to launch.

The GT4 had about 8psi, and the R33 GTS-t had about 4-5psi.

They just had launch control, not anti lag !

J

i understand what your saying about changing gears, but i change gears as quick as most people if not quicker with shortshift kit, and the gearbox has been modified so that its easier to get the gears to change, but i don think it might be a tuning problem but ill find out soon from croydon on what can be changed to help me out.

  • 3 weeks later...
i got an email from fc datalogic in NZ the guy wrote that anti lag was possible on the standard power fc with the fc datalogic equipment, anyone know if this is true.

There are quite a few different ways of achieving anti lag, it would depend on which way you wanted to run yours.

i just wanan run it or the creek, i just bought a nos kit having it installed at the end of the week, so that will get me to the time i want, but anti lag sounds good to get an even beter time,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...