Jump to content
SAU Community

Trust/Greddy Plenum

Skyrine-Dave
 Share

Recommended Posts

Skyrine-Dave Mentor

Skyrine-Dave

Posted
Posted

Hey all,

I am just wondering a few things about these plenums..

a) Are they excactly the same?

B) do you need an adapted for the throttlebody, or is it moulded onto the end?

c) Does anything have to be changed at all?? (hose wises, fitting etc)

d) can you use an RB20/RB25 throttle body?

e) The GTiR pulsar throttle cable is needed?

If anyone can answer those questions it would be greatly appreciated.

Cheers :)

Dave

Link to comment
https://www.sau.com.au/forums/topic/36982-trustgreddy-plenum/
Share on other sites
Steve Grand Master

Steve

Posted
Posted
Hey all,

I am just wondering a few things about these plenums..  

a) Are they excactly the same?

B) do you need an adapted for the throttlebody, or is it moulded onto the end?

c) Does anything have to be changed at all?? (hose wises, fitting etc)

d) can you use an RB20/RB25 throttle body?

e) The GTiR pulsar throttle cable is needed?

If anyone can answer those questions it would be greatly appreciated.

Cheers :cheers:

Dave

a ) AFAIK

b + d ) the q45 TB will bolt up, or you use stock TB you need an adaptor, which is about $100 new

c ) some of the stock hoses need to be altered (shortened mainly), wires for the AAC and AC idle solenoids need to be lengthened, minor mods to fuel rail feed - there are instructions, with heaps of pictures, but they are in japanese - pretty easy to follow though. Also, water feed for the turbo needs to be modded (from memory). thats about all I can think of :)

e ) GTiR is fine, or you can alter (lengthen) the stock cable.

gtrken Grand Master

gtrken

Posted
Posted
Thanks for the info Steve!

I take it the TPS senor wire would have to be lengthened too... How much roughly will a Q45 set one back ?

No , the TPS wires reach with no mods and a Q45 80mm throttle body will set you back $300 upwards.

You will also need to change your intercooler piping and the big IAC pipe will have to find a home in the inlet pipe somewhere.

I think if you get the proper GReddy FMIC then it already has that pipe there.

Cheers

Ken

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...